EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

On the Springback and Load in Three-Point Air Bending of the AW-2024 Aluminium Alloy Sheet with AW-1050A Aluminium Cladding

Stanisław Kut iD, Grzegorz Pasowicz, Feliks Stachowicz iD

Materials · 07.04.2023 · 16 (8) · 2945

DOI: 10.3390/ma16082945 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 07.04.2023. Verfasst von Stanisław Kut und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Forming and Processing, Rzeszow University of Technology, al. Powstańców Warszawy 8, 35-959 Rzeszów, Poland. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 24 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This article presents the results of an analysis of the bending load characteristics and the springback phenomenon occurring during three-point bending of 1.0 and 2.0 mm thick AW-2024 aluminium alloy sheets with rolled AW-1050A cladding. A new proprietary equation was proposed for determining the bending angle as a function of deflection, which takes into account the influence of the tool radius and the sheet thickness. The experimentally determined springback and bending load characteristics were compared with the results of numerical modelling using different models: Model I, a 2D model for a plane deformation state, disregarding the material properties of the clad layers; Model II, a 2D model for a plane deformation state, taking into account the material properties of the cladding layers; Model III, a 3D shell model with the Huber–von Mises isotropic plasticity condition; Model IV, a 3D shell model with the Hill anisotropic plasticity condition; and Model V, a 3D shell model with the Barlat anisotropic plasticity condition. The effectiveness of these five tested FEM models in predicting the bending load and springback characteristics was demonstrated. Model II was the most effective in predicting bending load, while Model III was the most effective in predicting the amount of springback after bending.

Schlagwörter

Stichwörter der Autor:innen

bending loadclad sheet metalspringbackthree-point air bending

Autor:innen und Institutionen

  • Department of Materials Forming and Processing, Rzeszow University of Technology, al. Powstańców Warszawy 8, 35-959 Rzeszów, Poland.
  • Doctoral School of the Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland.

ORCID-Profile: Stanisław Kut, Feliks Stachowicz

Zitieren

APA

Kut, S., Pasowicz, G., & Stachowicz, F. (2023). On the Springback and Load in Three-Point Air Bending of the AW-2024 Aluminium Alloy Sheet with AW-1050A Aluminium Cladding. Materials, 16(8), 2945. https://doi.org/10.3390/ma16082945

Vancouver

Kut S, Pasowicz G, Stachowicz F. On the Springback and Load in Three-Point Air Bending of the AW-2024 Aluminium Alloy Sheet with AW-1050A Aluminium Cladding. Materials. 2023;16(8):2945. doi:10.3390/ma16082945

BibTeX
@article{Kut2023,
  author = {Kut, Stanisław and Pasowicz, Grzegorz and Stachowicz, Feliks},
  title = {On the Springback and Load in Three-Point Air Bending of the AW-2024 Aluminium Alloy Sheet with AW-1050A Aluminium Cladding},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {8},
  pages = {2945},
  doi = {10.3390/ma16082945}
}
Kostenlos starten →