EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Nanoval Technology—An Intermediate Process between Meltblown and Spunbond

Tim Höhnemann iD, Johannes Schnebele, Walter Arne, Ingo Windschiegl

Materials · 06.04.2023 · 16 (7) · 2932

DOI: 10.3390/ma16072932 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 06.04.2023. Verfasst von Tim Höhnemann und 3 weiteren Autor:innen. Beteiligte Einrichtung: German Institutes of Textile and Fiber Research (DITF), Koerschtalstr. 26, D-73770 Denkendorf, Germany. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Federal Ministry for Economic Affairs and Energy, AiF ZIM.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The idea of ”Nanoval technology“ origins in the metal injection molding for gas atomization of metal powders and the knowledge of spunbond technologies for the creation of thermoplastic nonwovens using the benefits of both techniques. In this study, we evaluated processing limits experimentally for the spinning of different types of polypropylene, further standard polymers, and polyphenylene sulfide, marked by defect-free fiber creation. A numerical simulation study of the turbulent air flow as well as filament motion in the process visualized that the turnover from uniaxial flow (initial stretching caused by the high air velocity directed at the spinning die) to turbulent viscoelastic behavior occurs significantly earlier than in the melt-blown process. Modeling of the whole process showed that additional guide plates below the spinneret reduce the turbulent air flow significantly by regulating the inflow of secondary process air. The corresponding melt flow index of processible polymer grades varied between 35 g·10min−1 up to 1200 g·10min−1 and thus covering the range of extrusion-type, spunbond-type, yarn-type, and meltblown-type polymers. Hence, mean fiber diameters were adjustable for PP between 0.8 and 39.3 μm without changing components of the process setup. This implies that the Nanoval process enables the flexibility to produce fiber diameters in the typical range achievable by the standard meltblown process (~1–7 μm) as well as in the coarseness of spunbond nonwovens (15–30 μm) and, moreover, operates in the gap between them.

Schlagwörter

Stichwörter der Autor:innen

fibersmeltblownmodelingnonwovensnumerical simulationspolymersprocessingrheologyspinningspunbond

Autor:innen und Institutionen

  • German Institutes of Textile and Fiber Research (DITF), Koerschtalstr. 26, D-73770 Denkendorf, Germany.
  • Fraunhofer Institute for Industrial Mathematics (ITWM), Fraunhofer Platz 1, D-67663 Kaiserslautern, Germany.

ORCID-Profile: Tim Höhnemann

Förderung

  • Federal Ministry for Economic Affairs and Energy
  • AiF ZIM

Zitieren

APA

Höhnemann, T., Schnebele, J., Arne, W., & Windschiegl, I. (2023). Nanoval Technology—An Intermediate Process between Meltblown and Spunbond. Materials, 16(7), 2932. https://doi.org/10.3390/ma16072932

Vancouver

Höhnemann T, Schnebele J, Arne W, Windschiegl I. Nanoval Technology—An Intermediate Process between Meltblown and Spunbond. Materials. 2023;16(7):2932. doi:10.3390/ma16072932

BibTeX
@article{Hhnemann2023,
  author = {Höhnemann, Tim and Schnebele, Johannes and Arne, Walter and Windschiegl, Ingo},
  title = {Nanoval Technology—An Intermediate Process between Meltblown and Spunbond},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {7},
  pages = {2932},
  doi = {10.3390/ma16072932}
}
Kostenlos starten →