Effect of Cutting Fluid on Milled Surface Quality and Tool Life of Aluminum Alloy
Materials · 09.03.2023 · 16 (6) · 2198
DOI: 10.3390/ma16062198 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 09.03.2023. Verfasst von Shuoshuo Pang und 6 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical Engineering, Beijing Institute of Technology, No. 5 Zhongguancun South Street, Haidian District, Beijing 100081, China. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Key Research and Development Program of China.
Abstract (Originalsprache)
The machining process of aluminum alloy usually produces built-up edge and tool sticking problems due to their low hardness and large plastic deformation, which may further affect the machined surface quality and tool life. This paper aims to investigate the influence of different cutting fluids on the machined surface quality and tool life during the milling process of 7050 aluminum alloy. A novel cutting fluid (QC-2803) was considered in the study, which is synthesized by addition of alkyl alcohol amide and chlorinated polyolefin, and the traditional cutting fluid (CCF-10) was used as the control group. The physical and chemical properties of two cutting fluids were characterized. The milling process of 7050 aluminum alloy was carried out under two different cutting fluid conditions. The machined surface morphology, cutting force and tool wear morphology were observed during the process. Results show that the surface tension of the novel cutting fluid is significantly lower than that of the traditional cutting fluid, which makes it easier to produce a lubricating film between the aluminum alloy and tool, and further benefits the machined surface quality and tool life. As a result, the surface roughness and cutting force are reduced by ~20.0% and ~42.9%, respectively, and the tool life is increased by 25.6% in the case of the novel cutting fluid (QC-2803). The results in this paper revealed the important laws of cutting fluid with metal surface quality, cutting performance and tool wear, which helps to control the machined surface quality and tool life by the selection of cutting fluid during metal milling.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- School of Mechanical Engineering, Beijing Institute of Technology, No. 5 Zhongguancun South Street, Haidian District, Beijing 100081, China.
- Key Laboratory of Fundamental Science for Advanced Machining Beijing Institute of Technology, No. 5 Zhongguancun South Street, Haidian District, Beijing 100081, China.
Förderung
- National Key Research and Development Program of China
Zitieren
APA
Pang, S., Zhao, W., Qiu, T., Liu, W., Yan, P., Jiao, L., & Wang, X. (2023). Effect of Cutting Fluid on Milled Surface Quality and Tool Life of Aluminum Alloy. Materials, 16(6), 2198. https://doi.org/10.3390/ma16062198
Vancouver
Pang S, Zhao W, Qiu T, Liu W, Yan P, Jiao L, et al. Effect of Cutting Fluid on Milled Surface Quality and Tool Life of Aluminum Alloy. Materials. 2023;16(6):2198. doi:10.3390/ma16062198
BibTeX
@article{Pang2023,
author = {Pang, Shuoshuo and Zhao, Wenxiang and Qiu, Tianyang and Liu, Weiliang and Yan, Pei and Jiao, Li and Wang, Xibin},
title = {Effect of Cutting Fluid on Milled Surface Quality and Tool Life of Aluminum Alloy},
journal = {Materials},
year = {2023},
volume = {16},
number = {6},
pages = {2198},
doi = {10.3390/ma16062198}
}
EUVIMED