EUVIMEDEUVIMED entdecken
ÜbersichtsarbeitOpen Access · CC BY 4.0

Clinically Relevant Properties of 3D Printable Materials for Intraoral Use in Orthodontics: A Critical Review of the Literature

Cecilia Goracci, Jovana Juloski iD, Claudio D'Amico, Dario Balestra, Alessandra Volpe, Jelena Juloski iD, Alessandro Vichi

Materials · 08.03.2023 · 16 (6) · 2166

DOI: 10.3390/ma16062166 ↗

Kurz gefasst

Übersichtsarbeit in der Zeitschrift Materials, online erschienen am 08.03.2023. Verfasst von Cecilia Goracci und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Medical Biotechnologies, University of Siena, 53100 Siena, Italy. Die Arbeit wurde bisher 55-mal zitiert (Crossref) und nennt 64 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The review aimed at analyzing the evidence available on 3D printable materials and techniques used for the fabrication of orthodontic appliances, focusing on materials properties that are clinically relevant. MEDLINE/PubMed, Scopus, and Cochrane Library databases were searched. Starting from an initial retrieval of 669 citations, 47 articles were finally included in the qualitative review. Several articles presented proof-of-concept clinical cases describing the digital workflow to manufacture a variety of appliances. Clinical studies other than these case reports are not available. The fabrication of aligners is the most investigated application of 3D printing in orthodontics, and, among materials, Dental LT Clear Resin (Formlabs) has been tested in several studies, although Tera Harz TC-85 (Graphy) is currently the only material specifically marketed for direct printing of aligners. Tests of the mechanical properties of aligners materials lacked homogeneity in the protocols, while biocompatibility tests failed to assess the influence of intraoral conditions on eluents release. The aesthetic properties of 3D-printed appliances are largely unexplored. The evidence on 3D-printed metallic appliances is also limited. The scientific evidence on 3D printable orthodontic materials and techniques should be strengthened by defining international standards for laboratory testing and by starting the necessary clinical trials.

Schlagwörter

Stichwörter der Autor:innen

3D printingadditive manufacturingmaterialsorthodonticsrapid prototypingreview

Autor:innen und Institutionen

  • Department of Medical Biotechnologies, University of Siena, 53100 Siena, Italy.
  • Department of Orthodontics, School of Dental Medicine, University of Belgrade, 11000 Belgrade, Serbia.
  • School of Dental Medicine, Alfonso X El Sabio University, 28691 Madrid, Spain.
  • Clinic for Paediatric and Preventive Dentistry, School of Dental Medicine, University of Belgrade, 11000 Belgrade, Serbia.
  • Dental Academy, University of Portsmouth, Portsmouth PO1 2QG, UK.

ORCID-Profile: Jovana Juloski, Jelena Juloski

Zitieren

APA

Goracci, C., Juloski, J., D'Amico, C., Balestra, D., Volpe, A., Juloski, J., & Vichi, A. (2023). Clinically Relevant Properties of 3D Printable Materials for Intraoral Use in Orthodontics: A Critical Review of the Literature. Materials, 16(6), 2166. https://doi.org/10.3390/ma16062166

Vancouver

Goracci C, Juloski J, D'Amico C, Balestra D, Volpe A, Juloski J, et al. Clinically Relevant Properties of 3D Printable Materials for Intraoral Use in Orthodontics: A Critical Review of the Literature. Materials. 2023;16(6):2166. doi:10.3390/ma16062166

BibTeX
@article{Goracci2023,
  author = {Goracci, Cecilia and Juloski, Jovana and D'Amico, Claudio and Balestra, Dario and Volpe, Alessandra and Juloski, Jelena and Vichi, Alessandro},
  title = {Clinically Relevant Properties of 3D Printable Materials for Intraoral Use in Orthodontics: A Critical Review of the Literature},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {6},
  pages = {2166},
  doi = {10.3390/ma16062166}
}
Kostenlos starten →