EUVIMEDEUVIMED entdecken
ÜbersichtsarbeitOpen Access · CC BY 4.0

Ultra-High-Molecular-Weight Polyethylene in Hip and Knee Arthroplasties

Masahiro Hasegawa iD, Shine Tone, Yohei Naito, Akihiro Sudo iD

Materials · 07.03.2023 · 16 (6) · 2140

DOI: 10.3390/ma16062140 ↗

Kurz gefasst

Übersichtsarbeit in der Zeitschrift Materials, online erschienen am 07.03.2023. Verfasst von Masahiro Hasegawa und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Orthopaedic Surgery, Mie University Graduate School of Medicine, Tsu 514-8507, Japan. Die Arbeit wurde bisher 42-mal zitiert (Crossref) und nennt 113 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Ultra-high-molecular-weight polyethylene (UHMWPE) wear and particle-induced osteolysis contribute to the failure of total hip arthroplasty (THA) and total knee arthroplasty (TKA). Highly crosslinked polyethylene (HXLPE) was developed in the late 1990s to reduce wear and has shown lower wear rates and loosening than conventional UHMWPE in THA. The irradiation dose for crosslinking is up to 100 kGy. However, during crosslinking, free radical formation induces oxidation. Using HXLPE in THA, the cumulative revision rate was determined to be significantly lower (6.2%) than that with conventional UHMWPE (11.7%) at a mean follow-up of 16 years, according to the Australian Orthopaedic Association National Joint Replacement Registry. However, HXLPE does not confer to TKA the same advantages it confers to THA. Several alternatives have been developed to prevent the release of free radicals and improve polymer mechanical properties, such as thermal treatment, phospholipid polymer 2-methacryloyloxyethyl phosphorylcholine grafting, remelting, and vitamin E addition. Among these options, vitamin E addition has reported good clinical results and wear resistance similar to that of HXLPE without vitamin E, as shown by short-term clinical studies of THA and TKA. This review aims to provide a comprehensive overview of the development and performance of UHMWPE in THA and TKA.

Schlagwörter

Stichwörter der Autor:innen

arthroplastyhighly crosslinked polyethylenehipkneeoxidationultra-high-molecular-weight polyethylenevitamin E

Autor:innen und Institutionen

  • Department of Orthopaedic Surgery, Mie University Graduate School of Medicine, Tsu 514-8507, Japan.

ORCID-Profile: Masahiro Hasegawa, Akihiro Sudo

Zitieren

APA

Hasegawa, M., Tone, S., Naito, Y., & Sudo, A. (2023). Ultra-High-Molecular-Weight Polyethylene in Hip and Knee Arthroplasties. Materials, 16(6), 2140. https://doi.org/10.3390/ma16062140

Vancouver

Hasegawa M, Tone S, Naito Y, Sudo A. Ultra-High-Molecular-Weight Polyethylene in Hip and Knee Arthroplasties. Materials. 2023;16(6):2140. doi:10.3390/ma16062140

BibTeX
@article{Hasegawa2023,
  author = {Hasegawa, Masahiro and Tone, Shine and Naito, Yohei and Sudo, Akihiro},
  title = {Ultra-High-Molecular-Weight Polyethylene in Hip and Knee Arthroplasties},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {6},
  pages = {2140},
  doi = {10.3390/ma16062140}
}
Kostenlos starten →