Influence of Polycaprolactone Concentration and Solvent Type on the Dimensions and Morphology of Electrosprayed Particles
Materials · 06.03.2023 · 16 (5) · 2122
DOI: 10.3390/ma16052122 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 06.03.2023. Verfasst von Laura Alberto und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Biomedical Materials Science, University of Mississippi Medical Center, Jackson, MS 39216, USA. Die Arbeit wurde bisher 24-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Osteo Science Foundation.
Abstract (Originalsprache)
Polycaprolactone (PCL) micro- and nanoparticles produced using the electrospraying technique present high drug encapsulation capacity, a controllable surface area, and a good cost–benefit ratio. PCL is also considered a non-toxic polymeric material with excellent biocompatibility and biodegradability. All these characteristics make PCL micro- and nanoparticles a promising material for tissue engineering regeneration, drug delivery, and surface modification in dentistry. In this study, PCL electrosprayed specimens were produced and analyzed to determine their morphology and size. Three PCL concentrations (2, 4, and 6 wt%) and three solvent types (chloroform (CF), dimethylformamide (DMF), and acetic acid (AA)) with various solvent mixtures ratios (1:1 CF/DMF, 3:1 CF/DMF, 100% CF, 1:1 AA/CF, 3:1 AA/CF, and 100% AA) were used while keeping the remaining electrospray parameters constant. SEM images followed by ImageJ analysis showed a change in the morphology and size of the particles among various tested groups. A two-way ANOVA demonstrated a statistically significant interaction (p < 0.001) between PCL concentration and solvents on the size of the particles. With the increase in the PCL concentration, an increase in the number of fibers was observed among all the groups. The morphology and dimensions of the electrosprayed particles, as well as the presence of fibers, were significantly dependent on the PCL concentration, choice of solvent, and solvent ratio.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Biomedical Materials Science, University of Mississippi Medical Center, Jackson, MS 39216, USA.
- Department of Chemistry, Physics and Atmospheric Sciences, Jackson State University, Jackson, MS 39216, USA.
ORCID-Profile: Laura Alberto, Lohitha Kalluri
Förderung
- Osteo Science Foundation
Zitieren
APA
Alberto, L., Kalluri, L., Qu, J., Zhao, Y., & Duan, Y. (2023). Influence of Polycaprolactone Concentration and Solvent Type on the Dimensions and Morphology of Electrosprayed Particles. Materials, 16(5), 2122. https://doi.org/10.3390/ma16052122
Vancouver
Alberto L, Kalluri L, Qu J, Zhao Y, Duan Y. Influence of Polycaprolactone Concentration and Solvent Type on the Dimensions and Morphology of Electrosprayed Particles. Materials. 2023;16(5):2122. doi:10.3390/ma16052122
BibTeX
@article{Alberto2023,
author = {Alberto, Laura and Kalluri, Lohitha and Qu, Jing and Zhao, Yongfeng and Duan, Yuanyuan},
title = {Influence of Polycaprolactone Concentration and Solvent Type on the Dimensions and Morphology of Electrosprayed Particles},
journal = {Materials},
year = {2023},
volume = {16},
number = {5},
pages = {2122},
doi = {10.3390/ma16052122}
}
EUVIMED