Machining Strategy Determination for Single- and Multi-Material Wire and Arc Additive Manufactured Thin-Walled Parts
Materials · 02.03.2023 · 16 (5) · 2055
DOI: 10.3390/ma16052055 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 02.03.2023. Verfasst von Ozan Can Ozaner und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Engineering, Faculty of Engineering Technology, KU Leuven, Campus De Nayer, 2860 Sint-Katelijne Waver, Belgium. Die Arbeit wurde bisher 22-mal zitiert (Crossref) und nennt 26 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: CELSA, Slovenian Research Agency.
Abstract (Originalsprache)
Wire and arc additive manufacturing (WAAM) technology has recently become attractive due to the fact of its high production capacity and flexible deposition strategy. One of the most prominent drawbacks of WAAM is surface irregularity. Therefore, WAAMed parts cannot be used as built; they require secondary machining operations. However, performing such operations is challenging due to the fact of high waviness. Selecting an appropriate cutting strategy is also challenging, because surface irregularity makes cutting forces unstable. The present research determines the most suitable machining strategy by assessing the specific cutting energy and local machined volume. Up- and down-milling are evaluated by calculating the removed volume and specific cutting energy for creep-resistant steel, stainless steel, and their combination. It is shown that the main factors that affect the machinability of WAAMed parts are the machined volume and specific cutting energy rather than the axial and radial depths of the cut due to the fact of high surface irregularity. Even though the results were unstable, a surface roughness of 0.1 µm was obtained with up-milling. Despite a two-fold difference in the hardness between the two materials in the multi-material deposition, it is found that hardness should not be used as a criterion for as-built surface processing. In addition, the results show no machinability difference between multi- and single-material components for a low machined volume and low surface irregularity.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Materials Engineering, Faculty of Engineering Technology, KU Leuven, Campus De Nayer, 2860 Sint-Katelijne Waver, Belgium.
- Faculty of Mechanical Engineering, University of Ljubljana, Aškerčeva 6, 1000 Ljubljana, Slovenia.
ORCID-Profile: Ozan Can Ozaner, Damjan Klobčar, Abhay Sharma
Förderung
- CELSA
- Slovenian Research Agency
Zitieren
APA
Ozaner, O. C., Klobčar, D., & Sharma, A. (2023). Machining Strategy Determination for Single- and Multi-Material Wire and Arc Additive Manufactured Thin-Walled Parts. Materials, 16(5), 2055. https://doi.org/10.3390/ma16052055
Vancouver
Ozaner OC, Klobčar D, Sharma A. Machining Strategy Determination for Single- and Multi-Material Wire and Arc Additive Manufactured Thin-Walled Parts. Materials. 2023;16(5):2055. doi:10.3390/ma16052055
BibTeX
@article{Ozaner2023,
author = {Ozaner, Ozan Can and Klobčar, Damjan and Sharma, Abhay},
title = {Machining Strategy Determination for Single- and Multi-Material Wire and Arc Additive Manufactured Thin-Walled Parts},
journal = {Materials},
year = {2023},
volume = {16},
number = {5},
pages = {2055},
doi = {10.3390/ma16052055}
}
EUVIMED