EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Guard Ring Design to Prevent Edge Breakdown in Double-Diffused Planar InGaAs/InP Avalanche Photodiodes

Yu-Chun Chen iD, Ruei-Hong Yan, Hsu-Chia Huang, Liang-Hsuan Nieh, Hao-Hsiung Lin

Materials · 16.02.2023 · 16 (4) · 1667

DOI: 10.3390/ma16041667 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 16.02.2023. Verfasst von Yu-Chun Chen und 4 weiteren Autor:innen. Beteiligte Einrichtung: Graduated Institute of Electronics Engineering, National Taiwan University, Taipei 10617, Taiwan. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 18 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science and Technology, ROC, National Chung-Shan Institute of Science and Technology, ROC.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

We report on the design of an attached guard ring (AGR) and a floating guard ring (FGR) in a planar separate absorption, grading, charge, and multiplication In0.53Ga0.47As/InP avalanche photodiode to prevent premature edge breakdowns. The depths of the two Zn diffusions were utilized to manipulate the guard ring structures. Results from TCAD simulation indicate that the optimal AGR diffusion depth is right at the turning point where the breakdown current shifts from the edge of active region to the AGR region. The devices with optimal AGR depth contain significantly higher breakdown voltages than those of devices either with shallower—or without any— AGR. For the FGR design, a series of devices with different spacings between AGR and FGR and different FGR opening widths for diffusion were fabricated and characterized. We show that when the spacing is longer than the critical value, the breakdown voltage can increase ~1.5 V higher than those of the APD devices without FGR. In addition, the wider the FGR opening width, the higher the breakdown voltage. TCAD simulations were also performed to study the effect of FGR, but showed less pronounced improvements, which could be due the discrepancy between the calculated and experimental diffusion profile.

Schlagwörter

Stichwörter der Autor:innen

APDInGaAsInPSAGCMdouble-diffusionedge breakdownguard ringphotonic device

Autor:innen und Institutionen

  • Graduated Institute of Electronics Engineering, National Taiwan University, Taipei 10617, Taiwan.
  • Graduated Institute of Photonics and Optoelectronics, National Taiwan University, Taipei 10617, Taiwan.
  • Department of Electrical Engineering, National Taiwan University, Taipei 10617, Taiwan.

ORCID-Profile: Yu-Chun Chen

Förderung

  • Ministry of Science and Technology, ROC
  • National Chung-Shan Institute of Science and Technology, ROC

Zitieren

APA

Chen, Y. C., Yan, R. H., Huang, H. C., Nieh, L. H., & Lin, H. H. (2023). Guard Ring Design to Prevent Edge Breakdown in Double-Diffused Planar InGaAs/InP Avalanche Photodiodes. Materials, 16(4), 1667. https://doi.org/10.3390/ma16041667

Vancouver

Chen YC, Yan RH, Huang HC, Nieh LH, Lin HH. Guard Ring Design to Prevent Edge Breakdown in Double-Diffused Planar InGaAs/InP Avalanche Photodiodes. Materials. 2023;16(4):1667. doi:10.3390/ma16041667

BibTeX
@article{Chen2023,
  author = {Chen, Yu-Chun and Yan, Ruei-Hong and Huang, Hsu-Chia and Nieh, Liang-Hsuan and Lin, Hao-Hsiung},
  title = {Guard Ring Design to Prevent Edge Breakdown in Double-Diffused Planar InGaAs/InP Avalanche Photodiodes},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {4},
  pages = {1667},
  doi = {10.3390/ma16041667}
}
Kostenlos starten →