EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Study on the Mechanical Properties of Cast-In-Situ Phosphogypsum as Building Material for Structural Walls

Qizhu Yang iD, Ze Xiang, Taoyong Liu, Changqing Deng iD, Huagang Zhang

Materials · 10.02.2023 · 16 (4) · 1481

DOI: 10.3390/ma16041481 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 10.02.2023. Verfasst von Qizhu Yang und 4 weiteren Autor:innen. Beteiligte Einrichtung: College of Civil Engineering and Architectural, Shaoyang University, Shaoyang 422000, China. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: This research was funded by Key Projects of Hunan Shaoyang Science and Technology Plan, Key Projects of Hunan Shaoyang Science and Technology Plan.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The application of cast-in-situ phosphogypsum as the wall material of building structures can greatly reduce the environmental pollution caused by phosphogypsum. Through the uniaxial compression test of cast-in-situ phosphogypsum specimens, the compressive strength of cast-in-situ phosphogypsum is determined, the constitutive relationship of the material is drawn up, and the elastic modulus and Poisson’s ratio of the material are determined. The results show that when the strain of the specimen is close to the peak strain, the cast-in-situ phosphogypsum has brittle properties and rapidly fails, where the failure state is mainly splitting failure. The retarder has a great influence on the peak stress. When the content of the retarder is about 0.3%, the peak stress is 8.6 MPa and the ultimate strain is 2.54 × 10−3, while the peak stress is 2.8 MPa and the ultimate strain is 2.01 × 10−3. The three segment constitutive fitted equations reflect all the characteristics of the compression specimen. When the strength of the cast-in-situ phosphogypsum is high, the elastic modulus is also high. When the content of the retarder is about 0.3%, the elastic modulus is 5300 MPa, and when the content of retarder is far greater than 0.3%, the elastic modulus is 2000 MPa. The Poisson’s ratio of material is recommended as 0.19.

Schlagwörter

Stichwörter der Autor:innen

Poisson’s ratiocast-in-situ phosphogypsumelastic modulusstress–strain curve

Autor:innen und Institutionen

  • College of Civil Engineering and Architectural, Shaoyang University, Shaoyang 422000, China.
  • Space Structures Research Center, Guizhou University, Guiyang 550025, China.

ORCID-Profile: Qizhu Yang, Changqing Deng

Förderung

  • This research was funded by Key Projects of Hunan Shaoyang Science and Technology Plan
  • Key Projects of Hunan Shaoyang Science and Technology Plan

Zitieren

APA

Yang, Q., Xiang, Z., Liu, T., Deng, C., & Zhang, H. (2023). Study on the Mechanical Properties of Cast-In-Situ Phosphogypsum as Building Material for Structural Walls. Materials, 16(4), 1481. https://doi.org/10.3390/ma16041481

Vancouver

Yang Q, Xiang Z, Liu T, Deng C, Zhang H. Study on the Mechanical Properties of Cast-In-Situ Phosphogypsum as Building Material for Structural Walls. Materials. 2023;16(4):1481. doi:10.3390/ma16041481

BibTeX
@article{Yang2023,
  author = {Yang, Qizhu and Xiang, Ze and Liu, Taoyong and Deng, Changqing and Zhang, Huagang},
  title = {Study on the Mechanical Properties of Cast-In-Situ Phosphogypsum as Building Material for Structural Walls},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {4},
  pages = {1481},
  doi = {10.3390/ma16041481}
}
Kostenlos starten →