EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Preliminary Studies into Cutting of a Novel Two Component 3D-Printed Stainless Steel–Polymer Composite Material by Abrasive Water Jet

Tomasz Szatkiewicz iD, Andrzej Perec iD, Aleksandra Radomska-Zalas iD, Kamil Banaszek iD, Blazej Balasz

Materials · 30.01.2023 · 16 (3) · 1170

DOI: 10.3390/ma16031170 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 30.01.2023. Verfasst von Tomasz Szatkiewicz und 4 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering, Koszalin University of Technology, 75-620 Koszalin, Poland. Die Arbeit wurde bisher 22-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Composites are materials with a heterogeneous structure, composed of two or more components with different properties. The properties of composites are never the sum or average of the properties of their components. There is a lot of research and many models on the different property assessments of composite materials. Composites are used as construction materials in key areas of technology, including in civil and mechanical engineering, aviation and space technology, and others. This work presents a modern composite material created with 3D-printing technology using the SLM method, and the possibility of its processing with one of the advanced manufacturing technologies, i.e., the Abrasive Water Jet (AWJ). Tests planned using DoE methods were carried out by changing control parameters such as the pressure, abrasive flow, and traverse speed. As a dependent parameter, the surface roughness parameter Sq (squared mean height) was selected and measured in different places of the cut composite. Based on the S/N ratio, the most favorable control parameters of the cutting process were also determined to achieve the lowest roughness of the cut surface. A clear effect of the controlled cutting process on the surface roughness was observed, as well as roughness variation for the metal and polymer component. In addition, the contact surface of the polymer with the metal in the cut zone was analyzed. Analysis of the contact surfaces on the microscope showed that the gap between the polymer–metal contact surfaces does not exceed 2.5 μm.

Schlagwörter

Stichwörter der Autor:innen

abrasive water jetcuttingmetal–polymer compositemodelingoptimizationsurface roughness

Autor:innen und Institutionen

  • Faculty of Mechanical Engineering, Koszalin University of Technology, 75-620 Koszalin, Poland.
  • Faculty of Technology, Jacob of Paradies University, 66-400 Gorzow Wielkopolski, Poland.
  • Doctoral School, Koszalin University of Technology, 75-620 Koszalin, Poland.

ORCID-Profile: Tomasz Szatkiewicz, Andrzej Perec, Aleksandra Radomska-Zalas, Kamil Banaszek

Zitieren

APA

Szatkiewicz, T., Perec, A., Radomska-Zalas, A., Banaszek, K., & Balasz, B. (2023). Preliminary Studies into Cutting of a Novel Two Component 3D-Printed Stainless Steel–Polymer Composite Material by Abrasive Water Jet. Materials, 16(3), 1170. https://doi.org/10.3390/ma16031170

Vancouver

Szatkiewicz T, Perec A, Radomska-Zalas A, Banaszek K, Balasz B. Preliminary Studies into Cutting of a Novel Two Component 3D-Printed Stainless Steel–Polymer Composite Material by Abrasive Water Jet. Materials. 2023;16(3):1170. doi:10.3390/ma16031170

BibTeX
@article{Szatkiewicz2023,
  author = {Szatkiewicz, Tomasz and Perec, Andrzej and Radomska-Zalas, Aleksandra and Banaszek, Kamil and Balasz, Blazej},
  title = {Preliminary Studies into Cutting of a Novel Two Component 3D-Printed Stainless Steel–Polymer Composite Material by Abrasive Water Jet},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {3},
  pages = {1170},
  doi = {10.3390/ma16031170}
}
Kostenlos starten →