A Comparison of Microstructure and Microhardness Properties of IN718 Fabricated via Powder- and Wire-Fed Laser-Directed Energy Deposition
Materials · 28.01.2023 · 16 (3) · 1129
DOI: 10.3390/ma16031129 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 28.01.2023. Verfasst von Nandana Menon und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, The Pennsylvania State University, University Park, PA 16802, USA. Die Arbeit wurde bisher 25-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Engineer Research and Development Center, Naval Sea Systems Command, Pennsylvania State University.
Abstract (Originalsprache)
The objective of this work is to compare the microstructure and microhardness properties of IN718 deposited by both powder- and wire-fed laser-directed energy deposition (L-DED) processes. The powder-fed L-DED is carried out on an Optomec LENS® system while the wire-fed L-DED is performed in an in-house custom-built system. Several single-layer single-track specimens are fabricated using different combinations of process parameters to down-select the optimal process parameters for both systems. The finalized parameters are, thereafter, used to build thin-wall specimens having identical designs. The specimens are characterized using optical and electron microscopy as well as microhardness measurements. The results demonstrate that the powder-fed specimen, built using optimal process parameters, does not exhibit any distortion. On the contrary, the wire-fed specimen, built with optimal process parameters, show lesser porosity. Differences in elemental segregation are also detected in the two specimens. For example, nitrides and carbides are observed in the wire-fed specimen but not in the powder-fed specimen. The microhardness measurements reveal the powder-fed specimen has higher microhardness values compared to the wire-fed specimen. These results can be used to fabricate parts with sequential powder and wire deposition to achieve biomimetic structures of varying microstructure and microhardness properties.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Mechanical Engineering, The Pennsylvania State University, University Park, PA 16802, USA.
- Applied Research Laboratory, The Pennsylvania State University, University Park, PA 16802, USA.
ORCID-Profile: Nandana Menon, Brady A Sawyer, Cory D Jamieson, Edward W Reutzel, Amrita Basak
Förderung
- Engineer Research and Development Center
- Naval Sea Systems Command
- Pennsylvania State University
- Office of Naval Research Manufacturing Technology Program and its Center of Excellence
- Institute for Manufacturing and Sustainment Technologies (iMAST) at the Applied Research Lab (ARL), Penn State
- editorial office of Materials, MDPI
Zitieren
APA
Menon, N., Sawyer, B. A., Jamieson, C. D., Reutzel, E. W., & Basak, A. (2023). A Comparison of Microstructure and Microhardness Properties of IN718 Fabricated via Powder- and Wire-Fed Laser-Directed Energy Deposition. Materials, 16(3), 1129. https://doi.org/10.3390/ma16031129
Vancouver
Menon N, Sawyer BA, Jamieson CD, Reutzel EW, Basak A. A Comparison of Microstructure and Microhardness Properties of IN718 Fabricated via Powder- and Wire-Fed Laser-Directed Energy Deposition. Materials. 2023;16(3):1129. doi:10.3390/ma16031129
BibTeX
@article{Menon2023,
author = {Menon, Nandana and Sawyer, Brady A and Jamieson, Cory D and Reutzel, Edward W and Basak, Amrita},
title = {A Comparison of Microstructure and Microhardness Properties of IN718 Fabricated via Powder- and Wire-Fed Laser-Directed Energy Deposition},
journal = {Materials},
year = {2023},
volume = {16},
number = {3},
pages = {1129},
doi = {10.3390/ma16031129}
}
EUVIMED