EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Finite Element Analysis of Split Sleeve Cold Expansion Process on Multiple Hole Aluminum Alloy

Yuan Lv, Meng'en Dong, Teng Zhang, Changkai Wang, Bo Hou, Changfan Li

Materials · 27.01.2023 · 16 (3) · 1109

DOI: 10.3390/ma16031109 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 27.01.2023. Verfasst von Yuan Lv und 5 weiteren Autor:innen. Beteiligte Einrichtung: College of Mechanical Engineering, Xi'an University of Science and Technology, Xi'an 710064, China. Die Arbeit wurde bisher 22-mal zitiert (Crossref) und nennt 44 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Special Scientific Research Program of Shaanxi Provincial Department of Education, Natural Science Basic Research Plan in Shaanxi Province of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Multiple cold expansion holes are widely used in connection areas of aircraft structures, in order to achieve uniform load transfer of the skin or connection parts. Split sleeve cold expansion (SSCE) is widely used to enhance the fatigue life of fastener holes by applying compressive residual stresses around the holes. In this study, the finite element method (FEM) was used to research the distribution and variation of residual stresses along the hole edges of 7075AA single-hole and multi-hole cold expansion (CE) specimens. Full-field strain measurements of single-hole and multi-hole specimens were performed using two-dimensional digital image correlation (DIC), and the residual stress and strain at the hole edge of the specimens measured by FEM and DIC were compared. FEM results shows that the maximum circumferential and radial residual stresses of three-hole specimens with three-hole spacing are increased by 5.37% and 31.53% compared with single-hole specimens. The maximum circumferential residual stress of three-hole specimens with four-hole spacing increases by 7.25% compared with a single hole, but the radial residual stress decreases by 12.98%. In addition, for three-hole specimens with hole spacing three times the hole diameter, the strengthening effect of SSCE in the order of middle hole, then left hole, and, finally, right hole is better than that of SSCE in the order of left to right hole. FEM and DIC full-field strain results are basically consistent.

Schlagwörter

Stichwörter der Autor:innen

7075 aluminum alloycompressive residual stressdigital image correlationfinite element methodsplit sleeve cold expansion

Autor:innen und Institutionen

  • College of Mechanical Engineering, Xi'an University of Science and Technology, Xi'an 710064, China.
  • Aviation Engineering School, Air Force Engineering University, Xi'an 710038, China.
  • Army Aviation Institute of PLA, Beijing 101100, China.

Förderung

  • National Natural Science Foundation of China
  • Special Scientific Research Program of Shaanxi Provincial Department of Education
  • Natural Science Basic Research Plan in Shaanxi Province of China

Zitieren

APA

Lv, Y., Dong, M., Zhang, T., Wang, C., Hou, B., & Li, C. (2023). Finite Element Analysis of Split Sleeve Cold Expansion Process on Multiple Hole Aluminum Alloy. Materials, 16(3), 1109. https://doi.org/10.3390/ma16031109

Vancouver

Lv Y, Dong M, Zhang T, Wang C, Hou B, Li C. Finite Element Analysis of Split Sleeve Cold Expansion Process on Multiple Hole Aluminum Alloy. Materials. 2023;16(3):1109. doi:10.3390/ma16031109

BibTeX
@article{Lv2023,
  author = {Lv, Yuan and Dong, Meng'en and Zhang, Teng and Wang, Changkai and Hou, Bo and Li, Changfan},
  title = {Finite Element Analysis of Split Sleeve Cold Expansion Process on Multiple Hole Aluminum Alloy},
  journal = {Materials},
  year = {2023},
  volume = {16},
  number = {3},
  pages = {1109},
  doi = {10.3390/ma16031109}
}
Kostenlos starten →