Hot Workability of the Multi-Size SiC Particle-Reinforced 6013 Aluminum Matrix Composites
Materials · 13.01.2023 · 16 (2) · 796
DOI: 10.3390/ma16020796 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 13.01.2023. Verfasst von Changlong Wu und 5 weiteren Autor:innen. Beteiligte Einrichtung: College of Materials Science and Engineering, Hunan University, Changsha 410082, China. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the Key Technologies R&D in Strategic Emerging Industries and Transformation in High-tech Achievements Program of Hunan Province, Key Technologies R&D in Strategic Emerging Industries and Transformation in the High-tech Achievements Program of Hunan Province.
Abstract (Originalsprache)
The size and distribution of ceramic particles in aluminum matrix composites have been reported to remarkably influence their properties. For a single ceramic particle, the particle size is too small and prone to agglomeration, which makes the mechanical properties of the composites worse. When the ceramic particle size is too large, the particles and alloy at the interface are not firmly bonded, and the effect of dispersion distribution is not achieved, which will also reduce the mechanical properties of the composites. The multi-size ceramic particles are expected to improve this situation, while their effect on hot workability is less studied. In this study, the hot deformation behavior, constitutive model, processing map and SEM microstructure were investigated to evaluate the hot workability of multi-size SiC particle-reinforced 6013 aluminum matrix composites. The results showed that the increased deformation temperature and decreased strain rate could decrease flow stresses. The flow stress behaviors of the composites can be described by the sine-hyperbolic Arrhenius equation with the deformation activation energy of Q = 205.863 kJ/mol. The constitutive equation of the composites is ε ˙=3.11592×1013sinh0.024909σ4.12413exp−205863RT. Then, the hot processing map of the SiCp/6013 composites was constructed and verified by SEM observations. The rheological instability zone was in the region of a high strain rate. The optimal processing zone for composites was 450~500 °C and 0.03~0.25 s−1. In addition, the strain level was found to increase both the Q value and the area of the instability zone.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- College of Materials Science and Engineering, Hunan University, Changsha 410082, China.
- Hunan Provincial Key Laboratory of Vehicle Power and Transmission System, Hunan Institute of Engineering, Xiangtan 411104, China.
ORCID-Profile: Fulin Jiang
Förderung
- the Key Technologies R&D in Strategic Emerging Industries and Transformation in High-tech Achievements Program of Hunan Province
- Key Technologies R&D in Strategic Emerging Industries and Transformation in the High-tech Achievements Program of Hunan Province
Zitieren
APA
Wu, C., Chen, S., Tang, J., Fu, D., Teng, J., & Jiang, F. (2023). Hot Workability of the Multi-Size SiC Particle-Reinforced 6013 Aluminum Matrix Composites. Materials, 16(2), 796. https://doi.org/10.3390/ma16020796
Vancouver
Wu C, Chen S, Tang J, Fu D, Teng J, Jiang F. Hot Workability of the Multi-Size SiC Particle-Reinforced 6013 Aluminum Matrix Composites. Materials. 2023;16(2):796. doi:10.3390/ma16020796
BibTeX
@article{Wu2023,
author = {Wu, Changlong and Chen, Shuang and Tang, Jie and Fu, Dingfa and Teng, Jie and Jiang, Fulin},
title = {Hot Workability of the Multi-Size SiC Particle-Reinforced 6013 Aluminum Matrix Composites},
journal = {Materials},
year = {2023},
volume = {16},
number = {2},
pages = {796},
doi = {10.3390/ma16020796}
}
EUVIMED