Microstructure Evolution, Constitutive Modelling, and Superplastic Forming of Experimental 6XXX-Type Alloys Processed with Different Thermomechanical Treatments
Materials · 03.01.2023 · 16 (1) · 445
DOI: 10.3390/ma16010445 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 03.01.2023. Verfasst von Andrey G Mochugovskiy und 5 weiteren Autor:innen. Beteiligte Einrichtung: Physical Metallurgy of Non-Ferrous Metals, National University of Science and Technology "MISIS," Leninsky Prospekt, 4, 119049 Moscow, Russia. Die Arbeit wurde bisher 22-mal zitiert (Crossref) und nennt 77 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Russian Science Foundation.
Abstract (Originalsprache)
This study focused on the microstructural analysis, superplasticity, modeling of superplastic deformation behavior, and superplastic forming tests of the Al-Mg-Si-Cu-based alloy modified with Fe, Ni, Sc, and Zr. The effect of the thermomechanical treatment with various proportions of hot/cold rolling degrees on the secondary particle distribution and deformation behavior was studied. The increase in hot rolling degree increased the homogeneity of the particle distribution in the aluminum-based solid solution that improved superplastic properties, providing an elongation of ~470–500% at increased strain rates of (0.5–1) × 10−2 s−1. A constitutive model based on Arrhenius and Beckofen equations was used to describe and predict the superplastic flow behavior of the alloy studied. Model complex-shaped parts were processed by superplastic forming at two strain rates. The proposed strain rate of 1 × 10−2 s−1 provided a low thickness variation and a high quality of the experimental parts. The residual cavitation after superplastic forming was also large at the low strain rate of 2 × 10−3 s−1 and significantly smaller at 1 × 10−2 s−1. Coarse Al9FeNi particles did not stimulate the cavitation process and were effective to provide the superplasticity of alloys studied at high strain rates, whereas cavities were predominately observed near coarse Mg2Si particles, which act as nucleation places for cavities during superplastic deformation and forming.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Physical Metallurgy of Non-Ferrous Metals, National University of Science and Technology "MISIS," Leninsky Prospekt, 4, 119049 Moscow, Russia.
- Mechanical Engineering Department, Faculty of Engineering at Shoubra, Benha University, Cairo 11629, Egypt.
- Institute of Mechanics, Lomonosov Moscow State University, Michurinskiy Prospect, 1, 119192 Moscow, Russia.
ORCID-Profile: Andrey G Mochugovskiy, Ahmed O Mosleh, Anton D Kotov
Förderung
- Russian Science Foundation
Zitieren
APA
Mochugovskiy, A. G., Mosleh, A. O., Kotov, A. D., Khokhlov, A. V., Kaplanskaya, L. Y., & Mikhaylovskaya, A. V. (2023). Microstructure Evolution, Constitutive Modelling, and Superplastic Forming of Experimental 6XXX-Type Alloys Processed with Different Thermomechanical Treatments. Materials, 16(1), 445. https://doi.org/10.3390/ma16010445
Vancouver
Mochugovskiy AG, Mosleh AO, Kotov AD, Khokhlov AV, Kaplanskaya LY, Mikhaylovskaya AV. Microstructure Evolution, Constitutive Modelling, and Superplastic Forming of Experimental 6XXX-Type Alloys Processed with Different Thermomechanical Treatments. Materials. 2023;16(1):445. doi:10.3390/ma16010445
BibTeX
@article{Mochugovskiy2023,
author = {Mochugovskiy, Andrey G and Mosleh, Ahmed O and Kotov, Anton D and Khokhlov, Andrey V and Kaplanskaya, Ludmila Yu and Mikhaylovskaya, Anastasia V},
title = {Microstructure Evolution, Constitutive Modelling, and Superplastic Forming of Experimental 6XXX-Type Alloys Processed with Different Thermomechanical Treatments},
journal = {Materials},
year = {2023},
volume = {16},
number = {1},
pages = {445},
doi = {10.3390/ma16010445}
}
EUVIMED