EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Microstructure–Tribology Relationship in Ti-6Al-4V Alloy After Short-Duration Low-Pressure Gas Nitriding

Chih-Hao Yang, Ching-Quan Tsai, Chang-Yu Li, Shih-Hsien Chang

Lubricants · 19.11.2026 · 14 (11) · 443

DOI: 10.3390/lubricants14110443 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Lubricants, online erschienen am 19.11.2026. Verfasst von Chih-Hao Yang und 3 weiteren Autor:innen. Die Arbeit nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Ti-6Al-4V alloy is widely used in aerospace, biomedical, and engineering applications because of its high specific strength, corrosion resistance, and biocompatibility. However, its relatively low surface hardness and poor wear resistance limit its use under sliding-contact conditions. In this study, Ti-6Al-4V specimens were subjected to low-pressure gas nitriding at 950 °C for 60, 100, and 130 min to investigate the effects of short nitriding time on microstructure, hardness, and tribological behavior. The nitrided layers were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), electron backscatter diffraction (EBSD), and X-ray diffraction (XRD). Cross-sectional microhardness, Rockwell C indentation, surface roughness, and dry sliding wear tests according to ASTM G99 were also evaluated. Low-pressure gas nitriding produced a graded surface region consisting mainly of a TiN/Ti2N compound layer and an α-Ti(N) diffusion zone. Increasing nitriding time promoted nitrogen penetration and development of the nitrided region. The N100 specimen exhibited the highest near-surface microhardness of approximately 550 HV0.025, whereas N130 showed a lower value of approximately 490 HV0.025. Despite its lower near-surface hardness than N100, N130 exhibited the lowest mean wear loss among the nitrided specimens, with a gravimetrically estimated wear volume of 0.722 ± 0.060 mm3 and a specific wear rate of (5.99 ± 0.50) × 10−4 mm3/(N·m). After correction using the adjacent unworn surfaces as references, the maximum wear depths in representative profiles were approximately 49.2, 47.8, and 23.3 μm for N60, N100, and N130, respectively. These depths exceeded the corresponding TiN/Ti2N compound-layer thicknesses of approximately 6–10 μm, indicating local penetration through the outer compound layer in all three conditions during prolonged sliding under a normal load of 4 N. The wear response did not follow the same trend as near-surface hardness, compound-layer thickness, or initial surface roughness, indicating that no single parameter alone governed material removal. Instead, the results suggest that the overall response of the graded nitrided region, including penetration depth, layer integrity, surface condition, and subsurface mechanical support, collectively influenced the tribological behavior. SEM and EDS observations were consistent with abrasive wear features accompanied by local adhesion, tribo-oxidation, delamination, and third-body interactions, although the relative contribution of each mechanism could not be determined conclusively. Under the present test condition, the untreated specimen exhibited the lowest overall wear volume, whereas N130 showed the lowest material loss among the nitrided specimens. The formation of an effective nitrided region within 60–130 min at 950 °C demonstrates the feasibility of short-duration LPGN and suggests potential reductions in processing time and thermal exposure.

Zitieren

APA

Yang, C., Tsai, C., Li, C., & Chang, S. (2026). Microstructure–Tribology Relationship in Ti-6Al-4V Alloy After Short-Duration Low-Pressure Gas Nitriding. Lubricants, 14(11), 443. https://doi.org/10.3390/lubricants14110443

Vancouver

Yang C, Tsai C, Li C, Chang S. Microstructure–Tribology Relationship in Ti-6Al-4V Alloy After Short-Duration Low-Pressure Gas Nitriding. Lubricants. 2026;14(11):443. doi:10.3390/lubricants14110443

BibTeX
@article{Yang2026,
  author = {Yang, Chih-Hao and Tsai, Ching-Quan and Li, Chang-Yu and Chang, Shih-Hsien},
  title = {Microstructure–Tribology Relationship in Ti-6Al-4V Alloy After Short-Duration Low-Pressure Gas Nitriding},
  journal = {Lubricants},
  year = {2026},
  volume = {14},
  number = {11},
  pages = {443},
  doi = {10.3390/lubricants14110443}
}
Kostenlos starten →