EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Laser Surface Texturing of AA1050 Aluminum to Enhance the Tribological Properties of PTFE Coatings with a Taguchi-Based Analysis

Timur Canel, Sinan Fidan, Mustafa Özgür Bora, Satılmış Ürgün, Demet Taşkan Ürgün, Mehmet İskender Özsoy

Lubricants · 15.01.2026 · 14 (1) · 39

DOI: 10.3390/lubricants14010039 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Lubricants, online erschienen am 15.01.2026. Verfasst von Timur Canel und 5 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Fiber laser surface texturing was applied to AA1050 aluminum to improve friction and wear performance of PTFE coatings. A Taguchi L16 design varied texture geometry (square, diamond, hexagon, circle), scanned area ratio (20% to 80%), and laser power (40 to 100 W) prior to primer plus PTFE topcoat deposition (25 to 35 µm). Dry reciprocating sliding against a 6 mm 100Cr6 ball was conducted at 20 N, 1 Hz, and 50 m, and wear track geometry was measured by non-contact profilometry. The non-textured reference exhibited an average COF of 0.143, whereas the lowest mean COF was achieved with diamond 60% and 40 W (0.095) and the highest with hexagon 60% and 100 W (0.156); hexagon 20% and 60 W matched the reference. ANOVA indicated scanned area ratio as the dominant contributor to COF (39.72%), followed by geometry (35.07%) and power (25.21%). Profilometry confirmed reduced coating penetration for optimized textures: the reference wear track was approximately 1240 µm wide and 82 µm deep, compared with 930 µm and 34 µm for square 80% and 40 W, 997 µm and 39 µm for diamond 60% and 40 W, and 965 µm and 36 µm for hexagon 40% and 40 W.

Zitieren

APA

Canel, T., Fidan, S., Bora, M. Ö., Ürgün, S., Ürgün, D. T., & Özsoy, M. İ. (2026). Laser Surface Texturing of AA1050 Aluminum to Enhance the Tribological Properties of PTFE Coatings with a Taguchi-Based Analysis. Lubricants, 14(1), 39. https://doi.org/10.3390/lubricants14010039

Vancouver

Canel T, Fidan S, Bora MÖ, Ürgün S, Ürgün DT, Özsoy Mİ. Laser Surface Texturing of AA1050 Aluminum to Enhance the Tribological Properties of PTFE Coatings with a Taguchi-Based Analysis. Lubricants. 2026;14(1):39. doi:10.3390/lubricants14010039

BibTeX
@article{Canel2026,
  author = {Canel, Timur and Fidan, Sinan and Bora, Mustafa Özgür and Ürgün, Satılmış and Ürgün, Demet Taşkan and Özsoy, Mehmet İskender},
  title = {Laser Surface Texturing of AA1050 Aluminum to Enhance the Tribological Properties of PTFE Coatings with a Taguchi-Based Analysis},
  journal = {Lubricants},
  year = {2026},
  volume = {14},
  number = {1},
  pages = {39},
  doi = {10.3390/lubricants14010039}
}
Kostenlos starten →