EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Automated Design, Evaluation, and Optimization of 2D Rotor Blade Sections for Tidal Stream Turbines Using HEEDS

Soonhyun Lee, Hyungju Kim, Sooyeon Kwon

Journal of Marine Science and Engineering · 24.06.2026 · 14 (13) · 1161

DOI: 10.3390/jmse14131161 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Marine Science and Engineering, online erschienen am 24.06.2026. Verfasst von Soonhyun Lee und 2 weiteren Autor:innen. Die Arbeit nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Oceans and Fisheries.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

An automated CFD-based workflow for the design, evaluation, and comparative optimization of 2D tidal-stream turbine blade sections is presented for early-stage design exploration. The workflow is intended to efficiently derive an improved section using a consistent and higher fidelity evaluation approach, which is particularly relevant for floating tidal concepts where the effective angle of attack can vary. HEEDS is used to manage a SHERPA optimization loop, while candidate geometries are regenerated in Rhino Grasshopper through a control point parameterization with thickness bounds and smooth interpolation. STAR-CCM+ simulations are executed in an automated manner and the resulting lift and drag responses are returned to HEEDS to evaluate performance over four representative angles of attack, 0, 3, 6, and 9 deg. A total of 1000 design evaluations are conducted for a baseline NACA 63–815 section at Reynolds number 1 × 107, using a two metric formulation that targets high mean lift to drag ratio while limiting the maximum drag coefficient within the same angle set. The optimization history shows rapid early improvement followed by a plateau and identifies a final best design at Design 746. Compared with the original section, the optimized section increases lift and improves the lift-to-drag ratio across the operating range, while keeping the peak drag constrained. Cavitation inception characteristics also improve, with the optimized section delaying inception at the same lift criterion and sustaining a cavitation free state at higher lift for the same cavitation number. Pressure coefficient distributions indicate that these changes are primarily associated with altered suction side loading in the front to mid chord region and modified pressure recovery behavior. A preliminary full 3D RANS CFD rotor comparison under a prescribed rotor geometry further shows that the optimized section can improve rotor power performance in the main operating TSR range, although the benefit becomes limited at high TSR.

Förderung

  • Ministry of Oceans and Fisheries

Zitieren

APA

Lee, S., Kim, H., & Kwon, S. (2026). Automated Design, Evaluation, and Optimization of 2D Rotor Blade Sections for Tidal Stream Turbines Using HEEDS. Journal of Marine Science and Engineering, 14(13), 1161. https://doi.org/10.3390/jmse14131161

Vancouver

Lee S, Kim H, Kwon S. Automated Design, Evaluation, and Optimization of 2D Rotor Blade Sections for Tidal Stream Turbines Using HEEDS. Journal of Marine Science and Engineering. 2026;14(13):1161. doi:10.3390/jmse14131161

BibTeX
@article{Lee2026,
  author = {Lee, Soonhyun and Kim, Hyungju and Kwon, Sooyeon},
  title = {Automated Design, Evaluation, and Optimization of 2D Rotor Blade Sections for Tidal Stream Turbines Using HEEDS},
  journal = {Journal of Marine Science and Engineering},
  year = {2026},
  volume = {14},
  number = {13},
  pages = {1161},
  doi = {10.3390/jmse14131161}
}
Kostenlos starten →