EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Prediction of Milling Deformation for Frame-Type Thin-Walled Parts Considering Workblank Initial Residual Stress and Milling Force

Lijie Ma, Shijie Ba, Yu Zhang, Hongwen Liu, Leyang Li, Fei Gao, Faping Zhang, Junjin Ma

Journal of Manufacturing and Materials Processing · 29.04.2025 · 9 (5) · 146

DOI: 10.3390/jmmp9050146 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Manufacturing and Materials Processing, online erschienen am 29.04.2025. Verfasst von Lijie Ma und 7 weiteren Autor:innen. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Henan province key R&D project, National Natural Science Foundation of China, State Department project of China.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Machining deformation is a key bottleneck that restricts the improvement of manufacturing accuracy of aviation thin-walled structural components, such as frames, beams, and wall panels. The initial residual stress of the workblank and the cutting load are the direct factors leading to machining deformation. Based on the initial residual stress measurement and the milling force test, a finite element prediction model for milling deformation of frame-type thin-walled parts with integrated consideration of initial residual stress and the milling force was established and experimentally verified in this study. Then, the influence of milling process factors, such as the frame processing sequence (FPS), the cutting path, and the single frame one-time removal depth (SFORD), on the milling deformation of frame-type parts was studied. The results showed that the established prediction model had high reliability and the prediction accuracy was improved by 6.7% compared with that when only considering the initial residual stress. A smaller machining deformation can be achieved through the use of the FPS to prioritize the width, direction, and symmetrical milling, as well as the inner loop cutting path, and the smaller SFORD. This study can provide a technical reference for the prediction and control of milling deformation of aviation thin-walled structural parts, especially frame-type thin-walled parts.

Förderung

  • Henan province key R&D project
  • National Natural Science Foundation of China
  • State Department project of China

Zitieren

APA

Ma, L., Ba, S., Zhang, Y., Liu, H., Li, L., Gao, F., Zhang, F., & Ma, J. (2025). Prediction of Milling Deformation for Frame-Type Thin-Walled Parts Considering Workblank Initial Residual Stress and Milling Force. Journal of Manufacturing and Materials Processing, 9(5), 146. https://doi.org/10.3390/jmmp9050146

Vancouver

Ma L, Ba S, Zhang Y, Liu H, Li L, Gao F, et al. Prediction of Milling Deformation for Frame-Type Thin-Walled Parts Considering Workblank Initial Residual Stress and Milling Force. Journal of Manufacturing and Materials Processing. 2025;9(5):146. doi:10.3390/jmmp9050146

BibTeX
@article{Ma2025,
  author = {Ma, Lijie and Ba, Shijie and Zhang, Yu and Liu, Hongwen and Li, Leyang and Gao, Fei and Zhang, Faping and Ma, Junjin},
  title = {Prediction of Milling Deformation for Frame-Type Thin-Walled Parts Considering Workblank Initial Residual Stress and Milling Force},
  journal = {Journal of Manufacturing and Materials Processing},
  year = {2025},
  volume = {9},
  number = {5},
  pages = {146},
  doi = {10.3390/jmmp9050146}
}
Kostenlos starten →