Microstructure and Mechanical Properties of the Electron-Beam Additive-Manufactured Mg-Zn-Zr Alloy
Journal of Manufacturing and Materials Processing · 15.11.2026 · 10 (11) · 512
DOI: 10.3390/jmmp10110512 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Manufacturing and Materials Processing, online erschienen am 15.11.2026. Verfasst von Veronika Utyaganova und 5 weiteren Autor:innen. Die Arbeit nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Russian Science Foundation.
Abstract (Originalsprache)
Fabrication of a ZK60 (Mg-Zn-Zr) magnesium alloy using electron-beam additive manufacturing (EBAM) is an exceptionally challenging task due to the low boiling point of Mg, high thermal stress, solidification cracking, and some physical limitations of the raw material. Here, for the first time, a thin-wall ZK60 alloy was successfully produced using the EBAM approach. The electron-beam processing was performed by utilizing a single-pass scanning strategy and exponential reduction in heat input. The initial ZK60 wire had a sharp texture and exhibited a two-phase mixture: α-Mg(Zn, Zr) + MgZn2 Laves phase. The as-printed ZK60 alloy, according to the comprehensive SEM/EDS, XRD, and TEM analysis, was characterized by a eutectic microstructure, including fine-crystalline (~11.6 ± 2.7 μm) α-grains and MgZn2 particles segregated along the grain boundaries, as well as a minor fraction of Mg51Zn20 particles, identified by TEM. Within the narrow transition zone that is adjacent to the substrate, additional segregations of Zn-Zr intermetallic compounds were revealed only by SEM. The upper welded layer of the wall, according to the XRD analysis, exhibited indirect evidence of anisotropic grain growth along the direction, perpendicular to the building direction. The grain structure was rich in dislocation-related defects. The gradients of mechanical stresses of the second kind were found in the matrix α-phase, which was also evidenced by a high microstrain level (0.05–0.07%). The EBAMed alloy had a yield strength of ~149 MPa, an ultimate tensile strength of ~282–290 MPa, and an elongation of ~23–28%.
Förderung
- Russian Science Foundation
Zitieren
APA
Utyaganova, V., Semin, V., Nazarov, D., Goncharov, A., Sliva, A., & Shishkin, D. (2026). Microstructure and Mechanical Properties of the Electron-Beam Additive-Manufactured Mg-Zn-Zr Alloy. Journal of Manufacturing and Materials Processing, 10(11), 512. https://doi.org/10.3390/jmmp10110512
Vancouver
Utyaganova V, Semin V, Nazarov D, Goncharov A, Sliva A, Shishkin D. Microstructure and Mechanical Properties of the Electron-Beam Additive-Manufactured Mg-Zn-Zr Alloy. Journal of Manufacturing and Materials Processing. 2026;10(11):512. doi:10.3390/jmmp10110512
BibTeX
@article{Utyaganova2026,
author = {Utyaganova, Veronika and Semin, Viktor and Nazarov, Denis and Goncharov, Alexey and Sliva, Andrey and Shishkin, Dmitriy},
title = {Microstructure and Mechanical Properties of the Electron-Beam Additive-Manufactured Mg-Zn-Zr Alloy},
journal = {Journal of Manufacturing and Materials Processing},
year = {2026},
volume = {10},
number = {11},
pages = {512},
doi = {10.3390/jmmp10110512}
}
EUVIMED