EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Surface Integrity of VAR-Cast Ti-48Al-2Cr-2Nb Alloy After W-EDM, Dry Milling and Subsequent Annealing Treatments

Valentín Miguel, Alberto Martínez-Martínez, Crina Radu, Cătălin Tâmpu, Enrique García-Martínez, María Carmen Manjabacas, Juana Coello

Journal of Manufacturing and Materials Processing · 02.11.2026 · 10 (11) · 474

DOI: 10.3390/jmmp10110474 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Manufacturing and Materials Processing, online erschienen am 02.11.2026. Verfasst von Valentín Miguel und 6 weiteren Autor:innen. Die Arbeit nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Union, European Regional Development Fund, Regional Government of Castilla-La Mancha.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The surface integrity of γ-TiAl alloys is critical for the performance and reliability of aerospace components due to their limited ductility and inherent brittleness. Although wire electrical discharge machining (W-EDM), milling and heat treatments are commonly employed during the manufacture of γ-TiAl parts, their combined influence on surface integrity remains insufficiently understood. This study investigates the effects of finishing operations and post-machining heat treatments on a Ti-48Al-2Cr-2Nb alloy produced by vacuum arc remelting (VAR). Specimens were sectioned by W-EDM and subsequently finished by dry milling. Surface integrity was evaluated through metallographic observations, microhardness measurements, and residual stress analysis, while annealing treatments between 700 and 1100 °C for 2 h were applied to assess the recovery of machining-induced alterations. W-EDM generated a cracked surface layer, revealing a significant limitation of this process for γ-TiAl components. Milling removed the damaged layer and produced a defect-free surface, however, it induced a plastically deformed subsurface region about 50 μm thick, accompanied by increased hardness and residual stresses. Annealing at 700 °C provided only partial recovery, whereas treatments at 900 °C and above promoted complete recrystallization of the affected layer, restoring hardness to values close to those of the bulk material. The results demonstrate that milling followed by annealing at 900 °C for 2 h effectively restores surface integrity without altering the bulk microstructure.

Förderung

  • European Union
  • European Regional Development Fund
  • Regional Government of Castilla-La Mancha
  • INNOCAM programme

Zitieren

APA

Miguel, V., Martínez-Martínez, A., Radu, C., Tâmpu, C., García-Martínez, E., Manjabacas, M. C., & Coello, J. (2026). Surface Integrity of VAR-Cast Ti-48Al-2Cr-2Nb Alloy After W-EDM, Dry Milling and Subsequent Annealing Treatments. Journal of Manufacturing and Materials Processing, 10(11), 474. https://doi.org/10.3390/jmmp10110474

Vancouver

Miguel V, Martínez-Martínez A, Radu C, Tâmpu C, García-Martínez E, Manjabacas MC, et al. Surface Integrity of VAR-Cast Ti-48Al-2Cr-2Nb Alloy After W-EDM, Dry Milling and Subsequent Annealing Treatments. Journal of Manufacturing and Materials Processing. 2026;10(11):474. doi:10.3390/jmmp10110474

BibTeX
@article{Miguel2026,
  author = {Miguel, Valentín and Martínez-Martínez, Alberto and Radu, Crina and Tâmpu, Cătălin and García-Martínez, Enrique and Manjabacas, María Carmen and Coello, Juana},
  title = {Surface Integrity of VAR-Cast Ti-48Al-2Cr-2Nb Alloy After W-EDM, Dry Milling and Subsequent Annealing Treatments},
  journal = {Journal of Manufacturing and Materials Processing},
  year = {2026},
  volume = {10},
  number = {11},
  pages = {474},
  doi = {10.3390/jmmp10110474}
}
Kostenlos starten →