EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

PCD Tool Wear Mechanism and Prediction in Laser–Ultrasonic Synergistic Milling of High-Volume-Fraction SiCp/Al Composites

Liquan Yang, Kun Zhao, Jianhao Qi, Erbo Liu, Sen Yuan, Qingqing Lü, Guangxi Li

Journal of Manufacturing and Materials Processing · 19.08.2026 · 10 (8) · 305

DOI: 10.3390/jmmp10080305 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Manufacturing and Materials Processing, online erschienen am 19.08.2026. Verfasst von Liquan Yang und 6 weiteren Autor:innen. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Henan Province Science and Technology Research and Development Joint Fund, Henan Key Research and Development and Promotion Special Project, Guizhou Institute of Technology Doctoral Startup Fund.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To address severe PCD tool wear during the milling of high-volume-fraction SiCp/Al composites, a synergistic milling process coupling pulsed laser pretreatment with ultrasonic vibration was proposed. Five-factor, four-level orthogonal experiments were conducted on 70 vol.% SiCp/Al composites to investigate the effects of milling speed, feed per tooth, cutting depth, laser power, and ultrasonic amplitude on milling forces and tool wear, and a tool wear prediction model was established. The results showed that the factors influencing tool wear, in descending order, were feed per tooth, cutting depth, milling speed, laser power, and ultrasonic amplitude. Appropriate laser power and ultrasonic amplitude reduced cutting loads and suppressed tool wear. The model achieved a coefficient of determination of 0.7887 and was statistically significant overall. The optimal parameter combination was 50 m/min, 0.02 mm/z, 0.1 mm, 60 W, and 3.5 μm, under which the tool wear loss was 1.0 mg, representing a reduction of 61.54% compared with the maximum-wear condition. The main wear modes of the PCD tool included rake-face grooving and fatigue spalling, flank-face abrasive wear, and cutting-edge micro-chipping. These findings provide a useful reference for the precision milling of SiCp/Al composites.

Förderung

  • Henan Province Science and Technology Research and Development Joint Fund
  • Henan Key Research and Development and Promotion Special Project
  • Guizhou Institute of Technology Doctoral Startup Fund
  • China Iron and Steel Education Society Fund Project

Zitieren

APA

Yang, L., Zhao, K., Qi, J., Liu, E., Yuan, S., Lü, Q., & Li, G. (2026). PCD Tool Wear Mechanism and Prediction in Laser–Ultrasonic Synergistic Milling of High-Volume-Fraction SiCp/Al Composites. Journal of Manufacturing and Materials Processing, 10(8), 305. https://doi.org/10.3390/jmmp10080305

Vancouver

Yang L, Zhao K, Qi J, Liu E, Yuan S, Lü Q, et al. PCD Tool Wear Mechanism and Prediction in Laser–Ultrasonic Synergistic Milling of High-Volume-Fraction SiCp/Al Composites. Journal of Manufacturing and Materials Processing. 2026;10(8):305. doi:10.3390/jmmp10080305

BibTeX
@article{Yang2026,
  author = {Yang, Liquan and Zhao, Kun and Qi, Jianhao and Liu, Erbo and Yuan, Sen and Lü, Qingqing and Li, Guangxi},
  title = {PCD Tool Wear Mechanism and Prediction in Laser–Ultrasonic Synergistic Milling of High-Volume-Fraction SiCp/Al Composites},
  journal = {Journal of Manufacturing and Materials Processing},
  year = {2026},
  volume = {10},
  number = {8},
  pages = {305},
  doi = {10.3390/jmmp10080305}
}
Kostenlos starten →