EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Multi-Objective Optimization of the Geometry of a Modular Friction Disk Cutter for Thermo-Friction Processing of Spur Gear Teeth

Ansagan Suleimenov, Karibek Sherov, Assylbek Kassenov, Assylkhan Mazdubay, Jamshid Ravshanov, Doniyor Isaev, Musurmon Juraev, Gulerke Tattimbek, Sayagul Tussupova, Davran Radjibaev, Zhanara Mussina

Journal of Manufacturing and Materials Processing · 03.07.2026 · 10 (7) · 235

DOI: 10.3390/jmmp10070235 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Manufacturing and Materials Processing, online erschienen am 03.07.2026. Verfasst von Ansagan Suleimenov und 10 weiteren Autor:innen. Die Arbeit nennt 20 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Committee of Science and Higher Education of the Ministry of Education and Science of the Republic of Kazakhstan.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study presents multi-objective geometric optimization of a modular friction disk cutter for spur gear thermo-friction processing within the ANSYS Workbench 2024 R1. The integrated workflow—Geometry → Steady-State Thermal → Static Structural → Design of Experiments → Response Surface → Response Surface Optimization—enables selection of a rational tool geometry within a single parametric model. Variable dimensions (a, b, c) describe the load-bearing part: a characterizes the transitional thin profile zone, b is the massive supporting part, and c is the intermediate disk thickness controlling thermo-mechanical load transmission. Dimension c most significantly influences equivalent stresses and directional deformation, while maximum temperature depends on combined a and c effects. Based on Response Surface Optimization, the rational solution domain is concentrated near a≈3 mm, b≈10 mm, and c≈4 mm, yielding P4≈33.306 MPa, P5≈295.93 °C, and P6≈−5.7488·10−5 m. These values demonstrate a sufficient calculated safety margin within the finite element framework, providing a technically justified direction for prototype manufacturing. Although currently evaluated as purely computational without direct full-scale physical measurements, these results establish a foundation for subsequent experimental validation using thermal imaging and optical deformation analysis. Future research will focus on transient thermo-mechanical modeling with impulse cooling and experimental verification.

Förderung

  • Committee of Science and Higher Education of the Ministry of Education and Science of the Republic of Kazakhstan

Zitieren

APA

Suleimenov, A., Sherov, K., Kassenov, A., Mazdubay, A., Ravshanov, J., Isaev, D., Juraev, M., Tattimbek, G., Tussupova, S., Radjibaev, D., & Mussina, Z. (2026). Multi-Objective Optimization of the Geometry of a Modular Friction Disk Cutter for Thermo-Friction Processing of Spur Gear Teeth. Journal of Manufacturing and Materials Processing, 10(7), 235. https://doi.org/10.3390/jmmp10070235

Vancouver

Suleimenov A, Sherov K, Kassenov A, Mazdubay A, Ravshanov J, Isaev D, et al. Multi-Objective Optimization of the Geometry of a Modular Friction Disk Cutter for Thermo-Friction Processing of Spur Gear Teeth. Journal of Manufacturing and Materials Processing. 2026;10(7):235. doi:10.3390/jmmp10070235

BibTeX
@article{Suleimenov2026,
  author = {Suleimenov, Ansagan and Sherov, Karibek and Kassenov, Assylbek and Mazdubay, Assylkhan and Ravshanov, Jamshid and Isaev, Doniyor and Juraev, Musurmon and Tattimbek, Gulerke and Tussupova, Sayagul and Radjibaev, Davran and Mussina, Zhanara},
  title = {Multi-Objective Optimization of the Geometry of a Modular Friction Disk Cutter for Thermo-Friction Processing of Spur Gear Teeth},
  journal = {Journal of Manufacturing and Materials Processing},
  year = {2026},
  volume = {10},
  number = {7},
  pages = {235},
  doi = {10.3390/jmmp10070235}
}
Kostenlos starten →