EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Hot-Pressing Temperature on the Microstructure and Mechanical Properties of LPBF-Manufactured Al-10Sn-10Pb Alloy

K. O. Akimov, A. L. Skorentsev, N. M. Rusin, V. E. Liharev, A. Yu. Nikonov, D. P. Il’yashchenko, A. I. Dmitriev

Journal of Manufacturing and Materials Processing · 28.05.2026 · 10 (6) · 185

DOI: 10.3390/jmmp10060185 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Manufacturing and Materials Processing, online erschienen am 28.05.2026. Verfasst von K. O. Akimov und 6 weiteren Autor:innen. Die Arbeit nennt 27 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Russian Science Foundation.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Laser powder bed fusion (LPBF) of aluminum matrix tribological composites holds high potential for advanced bearing applications, yet its widespread implementation is often constrained by high porosity and severe residual stresses. In this work, the influence of hot pressing (HP) temperature (100–400 °C) on the microstructure, substructural evolution, mechanical properties, and fracture mechanisms of the LPBF Al-10Sn-10Pb alloy was investigated to achieve simultaneous densification and matrix optimization. Processing was carried out at 300 MPa with a 30 min holding time. It was established that at temperatures >200 °C, near-full consolidation is achieved through liquid-assisted pore closure. Increasing the temperature leads to the coarsening of Sn and Pb inclusions and the disruption of the initial dispersed network of soft phases. Williamson–Hall analysis revealed a transition from dislocation accumulation at 100 °C (~15 × 1013 m−2) to dynamic recovery at 200 °C, followed by matrix recrystallization at higher temperatures. A combination of strength (up to 127 MPa) and ductility (~11%) is realized at 200 °C due to the synergy between remaining substructural strengthening and pore healing. At 300–400 °C, the strength decreases to 108–113 MPa with a concomitant increase in ductility to 34–44%. A shift in fracture mechanisms from quasi-brittle to ductile is shown; at 400 °C, the development of intergranular fracture associated with the influence of liquid phases is possible.

Förderung

  • Russian Science Foundation

Zitieren

APA

Akimov, K. O., Skorentsev, A. L., Rusin, N. M., Liharev, V. E., Nikonov, A. Y., Il’yashchenko, D. P., & Dmitriev, A. I. (2026). Influence of Hot-Pressing Temperature on the Microstructure and Mechanical Properties of LPBF-Manufactured Al-10Sn-10Pb Alloy. Journal of Manufacturing and Materials Processing, 10(6), 185. https://doi.org/10.3390/jmmp10060185

Vancouver

Akimov KO, Skorentsev AL, Rusin NM, Liharev VE, Nikonov AY, Il’yashchenko DP, et al. Influence of Hot-Pressing Temperature on the Microstructure and Mechanical Properties of LPBF-Manufactured Al-10Sn-10Pb Alloy. Journal of Manufacturing and Materials Processing. 2026;10(6):185. doi:10.3390/jmmp10060185

BibTeX
@article{Akimov2026,
  author = {Akimov, K. O. and Skorentsev, A. L. and Rusin, N. M. and Liharev, V. E. and Nikonov, A. Yu. and Il’yashchenko, D. P. and Dmitriev, A. I.},
  title = {Influence of Hot-Pressing Temperature on the Microstructure and Mechanical Properties of LPBF-Manufactured Al-10Sn-10Pb Alloy},
  journal = {Journal of Manufacturing and Materials Processing},
  year = {2026},
  volume = {10},
  number = {6},
  pages = {185},
  doi = {10.3390/jmmp10060185}
}
Kostenlos starten →