EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Dual Beam Laser Welding of Superduplex Stainless Steel: Microstructure, Mechanical Properties, and Electrochemical Behavior

Lucia Kopčanová, Tomáš Dvorák, María Angeles Arenas, Erika Hodúlová, Ana Conde, Miroslav Čavojský, Juan Jose de Damborenea, Martin Nosko, Nad’a Beronská

Journal of Manufacturing and Materials Processing · 21.05.2026 · 10 (5) · 181

DOI: 10.3390/jmmp10050181 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Manufacturing and Materials Processing, online erschienen am 21.05.2026. Verfasst von Lucia Kopčanová und 8 weiteren Autor:innen. Die Arbeit nennt 61 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Slovak Research and Development Agency, Scientific Grant Agency of the Ministry of Education, Science, Research, and Sport of the Slovak Republic, Slovak Academy of Sciences.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Dual beam laser welding of UNS S32750 superduplex stainless steel was performed to investigate the effect of beam-power distribution on microstructure and mechanical properties. Plates with a thickness of 3 mm were welded at a constant total power and travel speed using leading and lagging power splits of 50:50, 80:20, and 65:35. The heat affected zone width was metallographically estimated at approximately 100 µm for all conditions, consistent with comparable gross thermal exposure under constant nominal linear energy input (Ptotal/v). A slight modification to the power distribution altered the solidification texture and austenite morphology. The 50:50 configuration produced a refined ferritic matrix with a continuous network of grain boundaries, Widmanstätten, and intragranular acicular austenite. The 80:20 condition increased ferrite path continuity, while the 65:35 split produced an intermediate morphology. Vickers hardness reached a maximum for the 80:20 split (HAZ: 345 HV; weld metal: 349 HV). Ultimate tensile strength remained statistically constant between 908 MPa and 914 MPa, whereas elongation decreased from 28% at 50:50 to 24% at 80:20 and 23% at 65:35. All welds exhibited ductile fracture with microvoid coalescence, and electrochemical performance was comparable, with critical pitting temperature values between 78 °C and 91 °C. Beam power distribution primarily affects solidification morphology and enables control of the hardness-to-ductility balance, with a 50:50 split providing the most favorable combination of properties.

Förderung

  • Slovak Research and Development Agency
  • Scientific Grant Agency of the Ministry of Education, Science, Research, and Sport of the Slovak Republic
  • Slovak Academy of Sciences
  • Spanish National Research Council

Zitieren

APA

Kopčanová, L., Dvorák, T., Arenas, M. A., Hodúlová, E., Conde, A., Čavojský, M., Damborenea, J. J. D., Nosko, M., & Beronská, N. (2026). Dual Beam Laser Welding of Superduplex Stainless Steel: Microstructure, Mechanical Properties, and Electrochemical Behavior. Journal of Manufacturing and Materials Processing, 10(5), 181. https://doi.org/10.3390/jmmp10050181

Vancouver

Kopčanová L, Dvorák T, Arenas MA, Hodúlová E, Conde A, Čavojský M, et al. Dual Beam Laser Welding of Superduplex Stainless Steel: Microstructure, Mechanical Properties, and Electrochemical Behavior. Journal of Manufacturing and Materials Processing. 2026;10(5):181. doi:10.3390/jmmp10050181

BibTeX
@article{Kopanov2026,
  author = {Kopčanová, Lucia and Dvorák, Tomáš and Arenas, María Angeles and Hodúlová, Erika and Conde, Ana and Čavojský, Miroslav and Damborenea, Juan Jose de and Nosko, Martin and Beronská, Nad’a},
  title = {Dual Beam Laser Welding of Superduplex Stainless Steel: Microstructure, Mechanical Properties, and Electrochemical Behavior},
  journal = {Journal of Manufacturing and Materials Processing},
  year = {2026},
  volume = {10},
  number = {5},
  pages = {181},
  doi = {10.3390/jmmp10050181}
}
Kostenlos starten →