EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Granulate-to-Filament: An Extrusion-Mixed PLA–Human Bone Material System for 3D-Printed Bone Scaffolds

Jonas Neijhoft iD, Hela Weslati, Volker Eras, Jan Brune iD, Maximilian Leiblein, Santiago Bianconi, Nicolas Söhling, Lewin Busse, René Verboket iD, Johannes Frank iD, Ingo Marzi iD, Dirk Henrich iD

Journal of Functional Biomaterials · 11.04.2026 · 17 (4) · 187

DOI: 10.3390/jfb17040187 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Functional Biomaterials, online erschienen am 11.04.2026. Verfasst von Jonas Neijhoft und 11 weiteren Autor:innen. Beteiligte Einrichtung: Department of Trauma and Orthopaedics, Goethe University Frankfurt, Jonas Neijhoft, Theodor-Stern-Kai 7, 60528 Frankfurt am Main, Germany. Die Arbeit nennt 67 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: German Institute for Cell and Tissue Replacement.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Fused filament fabrication (FFF) enables patient-specific scaffolds for critical-size bone defects, but most filaments are bioinert and difficult to functionalize at high particulate loadings due to segregation, agglomeration, clogging, and diameter instability. We developed a mechanism-guided extrusion toolkit to stabilize polylactic acid (PLA) filaments containing human demineralized bone matrix (DBM) or cortical granulate (CG) up to 70 wt%. PLA was ground, dried, silicone pre-coated, and compounded with DBM or CG (25/40/70 wt%) using starve-fed extrusion, sequential extrusion, and post-die mixing to maintain stable diameters. FFF produced disks and tubes. MSC adhesion was assessed by SEM. qPCR (control vs. osteogenic medium) quantified RUNX2, ALP, BGLAP, COL1A, VEGF, IL-6, MAPK8. Tubes underwent three-point bending. The toolkit yielded printable, dimensionally stable filaments at 25–70 wt% with uniform dispersion and surface-exposed filler. Both composites increased early mesenchymal stromal cells (MSC) adhesion versus PLA. RUNX2 was increased on DBM40 versus PLA. VEGF was elevated on CG25 (DBM40 trend). Under osteogenic medium, IL-6 and MAPK8 were generally reduced. Mechanics were loading-dependent: CG25 exceeded CG70 and DBM25, while DBM40/70 recovered stiffness versus DBM25. A mechanism-guided extrusion toolkit enables high-loading PLA–DBM/CG filaments with excellent printability and material-specific biological and mechanical advantages over PLA.

Schlagwörter

Stichwörter der Autor:innen

3D-printing diamond conceptadditive manufacturingbio-functionalizationbone tissue engineeringelectrostimulationimmunomodulationlong bone defectsmultifunctional scaffolds

Autor:innen und Institutionen

  • Department of Trauma and Orthopaedics, Goethe University Frankfurt, Jonas Neijhoft, Theodor-Stern-Kai 7, 60528 Frankfurt am Main, Germany.
  • German Institute for Cell and Tissue Replacement gGmbH (DIZG), 12555 Berlin, Germany.

ORCID-Profile: Jonas Neijhoft, Jan Brune, René Verboket, Johannes Frank, Ingo Marzi, Dirk Henrich

Förderung

  • German Institute for Cell and Tissue Replacement

Zitieren

APA

Neijhoft, J., Weslati, H., Eras, V., Brune, J., Leiblein, M., Bianconi, S., Söhling, N., Busse, L., Verboket, R., Frank, J., Marzi, I., & Henrich, D. (2026). Granulate-to-Filament: An Extrusion-Mixed PLA–Human Bone Material System for 3D-Printed Bone Scaffolds. Journal of Functional Biomaterials, 17(4), 187. https://doi.org/10.3390/jfb17040187

Vancouver

Neijhoft J, Weslati H, Eras V, Brune J, Leiblein M, Bianconi S, et al. Granulate-to-Filament: An Extrusion-Mixed PLA–Human Bone Material System for 3D-Printed Bone Scaffolds. Journal of Functional Biomaterials. 2026;17(4):187. doi:10.3390/jfb17040187

BibTeX
@article{Neijhoft2026,
  author = {Neijhoft, Jonas and Weslati, Hela and Eras, Volker and Brune, Jan and Leiblein, Maximilian and Bianconi, Santiago and Söhling, Nicolas and Busse, Lewin and Verboket, René and Frank, Johannes and Marzi, Ingo and Henrich, Dirk},
  title = {Granulate-to-Filament: An Extrusion-Mixed PLA–Human Bone Material System for 3D-Printed Bone Scaffolds},
  journal = {Journal of Functional Biomaterials},
  year = {2026},
  volume = {17},
  number = {4},
  pages = {187},
  doi = {10.3390/jfb17040187}
}
Kostenlos starten →