EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Additive vs. Subtractive Manufacturing of Zirconia: Influence on Surface Properties, Cell Viability, and Streptococcus mutans Adhesion

Ülkü Tuğba Kalyoncuoğlu iD, Nurten Baysal, Gulcin Akca, Simel Ayyıldız iD, Burak Yilmaz

Journal of Functional Biomaterials · 01.04.2026 · 17 (4) · 162

DOI: 10.3390/jfb17040162 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Functional Biomaterials, online erschienen am 01.04.2026. Verfasst von Ülkü Tuğba Kalyoncuoğlu und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Gülhane Faculty of Dentistry, University of Health Sciences Turkey, Ankara 06018, Turkey. Die Arbeit nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The surface characteristics of zirconia may influence both soft tissue response and bacterial colonization. This study evaluated the surface roughness and water contact angle of zirconia fabricated by additive manufacturing (material jetting, NPJ) and subtractive manufacturing (milling), and investigated human gingival fibroblast (HGF-1) viability and Streptococcus mutans (S. mutans) (ATCC 25175) adherence on these surfaces, as well as the possible correlation between roughness and bacterial adhesion. Sixty-four zirconia specimens (1 × 1 × 0.1 cm) were fabricated (n = 32 per group), sintered, and standardized by abrasive polishing. Surface roughness and contact angle were measured. Cell viability was assessed using an MTT assay at 24, 48, and 72 h. Bacterial adhesion was quantified after 24 and 48 h of incubation. Data were analyzed using two-way ANOVA, independent t-tests, and Pearson correlation (α = 0.05). No significant differences in HGF-1 viability were observed at 24 and 48 h; however, at 72 h, subtractively manufactured zirconia demonstrated higher cell viability than additively manufactured specimens (p < 0.001). S. mutans adhesion was significantly greater on additively manufactured zirconia at 24 h (p = 0.002), with no significant difference at 48 h. Manufacturing technique influenced surface properties and early bacterial adhesion. Both materials exhibited acceptable biocompatibility within the tested conditions.

Schlagwörter

Stichwörter der Autor:innen

3D printingStreptococcus mutanscell viabilityzirconia

Autor:innen und Institutionen

  • Department of Prosthodontics, Gülhane Faculty of Dentistry, University of Health Sciences Turkey, Ankara 06018, Turkey.
  • Department of Medical Microbiology, Faculty of Dentistry, Gazi University, Ankara 06490, Turkey.
  • Medical Design Manufacturing Center, University of Health Sciences Turkey, Ankara 06018, Turkey.
  • Laboratory for Digital Dental Technologies, Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, 3012 Bern, Switzerland.
  • Department of Restorative Preventive, and Pediatric Dentistry, School of Dental Medicine, University of Dental Medicine, 3010 Bern, Switzerland.
  • Department of Prosthodontics, Faculty of Dentistry, Ankara University, Ankara 06560, Turkey.

ORCID-Profile: Ülkü Tuğba Kalyoncuoğlu, Simel Ayyıldız

Zitieren

APA

Kalyoncuoğlu, Ü. T., Baysal, N., Akca, G., Ayyıldız, S., & Yilmaz, B. (2026). Additive vs. Subtractive Manufacturing of Zirconia: Influence on Surface Properties, Cell Viability, and Streptococcus mutans Adhesion. Journal of Functional Biomaterials, 17(4), 162. https://doi.org/10.3390/jfb17040162

Vancouver

Kalyoncuoğlu ÜT, Baysal N, Akca G, Ayyıldız S, Yilmaz B. Additive vs. Subtractive Manufacturing of Zirconia: Influence on Surface Properties, Cell Viability, and Streptococcus mutans Adhesion. Journal of Functional Biomaterials. 2026;17(4):162. doi:10.3390/jfb17040162

BibTeX
@article{Kalyoncuolu2026,
  author = {Kalyoncuoğlu, Ülkü Tuğba and Baysal, Nurten and Akca, Gulcin and Ayyıldız, Simel and Yilmaz, Burak},
  title = {Additive vs. Subtractive Manufacturing of Zirconia: Influence on Surface Properties, Cell Viability, and Streptococcus mutans Adhesion},
  journal = {Journal of Functional Biomaterials},
  year = {2026},
  volume = {17},
  number = {4},
  pages = {162},
  doi = {10.3390/jfb17040162}
}
Kostenlos starten →