Complete Digital Workflow for Manufacturing Presurgical Orthodontic Palatal Plates in Newborns and Infants with Cleft Lip and/or Palate
Journal of Functional Biomaterials · 08.10.2024 · 15 (10) · 301
DOI: 10.3390/jfb15100301 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Functional Biomaterials, online erschienen am 08.10.2024. Verfasst von Christina Weismann und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Orthodontics, University Hospital Tübingen, Osianderstr, 2-8, 72076 Tübingen, Germany. Die Arbeit wurde bisher 20-mal zitiert (Crossref) und nennt 79 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Deciding on the implementation or modification of steps in daily clinical care is a nuanced process that demands careful evaluation. This is crucial not only for selecting the most appropriate solution but also for achieving the best treatment outcome. Thus, implementing a workflow for treating cleft lip and/or palate patients with a presurgical orthodontic cleft-covering plate needs to consider objective factors, prioritized from most to least important: safety and quality level, user-friendliness, feasibility, and, finally, efficiency and cost. The goal of this workflow is to integrate CAD/CAM technologies into daily clinical routine to enhance technical and clinical efficiency, reduce the burden of cleft care, and simplify the implementation of these technologies in other facilities. To achieve this, a methodology based on intraoral scanning and additive manufacturing is employed to produce patient-specific passive palatal plates. The approach describes possible pitfalls and their resolution within the routine of a cleft centre, along with an exemplary case scenario. Comparative analysis between the digital workflow and the conventional process demonstrated the digital approach to be safer, higher in quality, more user-friendly, feasible, and cost- and time-effective than the conventional process.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Orthodontics, University Hospital Tübingen, Osianderstr, 2-8, 72076 Tübingen, Germany.
- Centre for Cleft Lip, Palate and Craniofacial Malformations, University Hospital Tübingen, Osianderstr, 2-8, 72076 Tübingen, Germany.
- Department of Oral and Maxillofacial Surgery, University Hospital Tübingen, Osianderstr, 2-8, 72076 Tübingen, Germany.
- Department of Neonatology, University Hospital Tübingen, Calwerstr, 7, 72076 Tübingen, Germany.
ORCID-Profile: Christina Weismann, Alexander B Xepapadeas, Marit Bockstedte, Michael Krimmel, Christian F Poets, Maite Aretxabaleta
Zitieren
APA
Weismann, C., Xepapadeas, A. B., Bockstedte, M., Koos, B., Krimmel, M., Poets, C. F., & Aretxabaleta, M. (2024). Complete Digital Workflow for Manufacturing Presurgical Orthodontic Palatal Plates in Newborns and Infants with Cleft Lip and/or Palate. Journal of Functional Biomaterials, 15(10), 301. https://doi.org/10.3390/jfb15100301
Vancouver
Weismann C, Xepapadeas AB, Bockstedte M, Koos B, Krimmel M, Poets CF, et al. Complete Digital Workflow for Manufacturing Presurgical Orthodontic Palatal Plates in Newborns and Infants with Cleft Lip and/or Palate. Journal of Functional Biomaterials. 2024;15(10):301. doi:10.3390/jfb15100301
BibTeX
@article{Weismann2024,
author = {Weismann, Christina and Xepapadeas, Alexander B and Bockstedte, Marit and Koos, Bernd and Krimmel, Michael and Poets, Christian F and Aretxabaleta, Maite},
title = {Complete Digital Workflow for Manufacturing Presurgical Orthodontic Palatal Plates in Newborns and Infants with Cleft Lip and/or Palate},
journal = {Journal of Functional Biomaterials},
year = {2024},
volume = {15},
number = {10},
pages = {301},
doi = {10.3390/jfb15100301}
}
EUVIMED