EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Parametric Analysis of CFRP Flexural Strengthening of Steel I-Beams Under Monotonic Loading

Pragyan Shrestha, Alaa Elsisi, Said Abdel-Monsef

Journal of Composites Science · 13.12.2025 · 9 (12) · 696

DOI: 10.3390/jcs9120696 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Composites Science, online erschienen am 13.12.2025. Verfasst von Pragyan Shrestha und 2 weiteren Autor:innen. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Externally bonded carbon-fiber-reinforced polymer (CFRP) can increase the flexural capacity of steel beams, but the benefit is often limited by the performance of the adhesive interface. This study develops and validates a three-dimensional finite-element model (FEM) with an explicit cohesive-zone representation of the adhesive layer. It reproduced benchmark four-point bending tests in terms of peak load, corresponding mid-span deflection, and the transition from end/intermediate debonding to laminate rupture. A one-factor-at-a-time parametric analysis is carried out to examine the influence of (i) member geometry (beam depth; flange and web thickness), (ii) CFRP configuration (bonded length; laminate thickness), and (iii) bond quality (cohesive normal strength). Within the ranges studied, cohesive strength and bonded length are the primary variables controlling both capacity and failure mode: strengths below about 25 MPa and short plates lead to debonding-governed response. Increasing strength to around 27 MPa and bonded length to 650–700 mm delays debonding, promotes CFRP rupture, and produces the largest incremental gains in peak load, while further increases in length give smaller additional gains. Increasing laminate thickness and steel depth or flange/web thickness always raises peak load, but under baseline bond conditions failure remains debonding and the added material is only partially mobilized. When cohesive strength is increased above the threshold, additional CFRP thickness becomes more effective. A linear regression model is fitted to the FEM dataset to express peak load as a function of bonded length, cohesive strength, laminate thickness, and steel dimensions, and is complemented by a failure-mode map and a cost–capacity chart based on material quantities. Together, these results provide quantitative trends and simple relations that can support preliminary design of CFRP-strengthened steel beams for similar configurations.

Zitieren

APA

Shrestha, P., Elsisi, A., & Abdel-Monsef, S. (2025). Parametric Analysis of CFRP Flexural Strengthening of Steel I-Beams Under Monotonic Loading. Journal of Composites Science, 9(12), 696. https://doi.org/10.3390/jcs9120696

Vancouver

Shrestha P, Elsisi A, Abdel-Monsef S. Parametric Analysis of CFRP Flexural Strengthening of Steel I-Beams Under Monotonic Loading. Journal of Composites Science. 2025;9(12):696. doi:10.3390/jcs9120696

BibTeX
@article{Shrestha2025,
  author = {Shrestha, Pragyan and Elsisi, Alaa and Abdel-Monsef, Said},
  title = {Parametric Analysis of CFRP Flexural Strengthening of Steel I-Beams Under Monotonic Loading},
  journal = {Journal of Composites Science},
  year = {2025},
  volume = {9},
  number = {12},
  pages = {696},
  doi = {10.3390/jcs9120696}
}
Kostenlos starten →