Mechanical Performance of Wood–Plastic Composites from Sawdust and Recycled Bottle Cap Polyolefins (PP/HDPE) for Temporary Concrete Formwork
Journal of Composites Science · 26.11.2025 · 9 (12) · 644
DOI: 10.3390/jcs9120644 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Composites Science, online erschienen am 26.11.2025. Verfasst von José Carlos Rosas Valencia und 6 weiteren Autor:innen. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 55 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Secretaría de Ciencia, Humanidades, Tecnología e Innovación, Fondo Sectorial CONAHCYT-SENER Sustentabilidad Energética, Centro Mexicano de Innovación en Energía Solar.
Abstract (Originalsprache)
This study quantifies the mechanical behavior of 10–15 mm thick WPC boards compression-molded from post-consumer bottle-cap polyolefins (PP/HDPE, 70/30 wt%) and pine sawdust (0, 10, 20 wt%). Flexural and tensile strength/modulus are determined and application-oriented acceptability assessed for non-structural temporary concrete formwork under ASTM bending and tension protocols. Mechanical performance was evaluated using three-point and four-point bending tests, as well as axial tension. Flexural strengths averaged 17.31, 16.38, and 8.71 MPa for 0, 10, and 20 wt% sawdust (three-points), and 15.23, 13.18, and 9.20 MPa (four-points), with flexural moduli as high as 1.60 GPa (four-points). Tensile strengths averaged 3.60, 3.79, and 3.44 MPa, with tensile elastic moduli of 0.10, 0.33, and 0.36 GPa, respectively. Stress–strain curves showed a nonlinear elastic-brittle response without a defined yield point, followed by fracture, consistent with porous, non-compatibilized WPCs. Variability increased with the sawdust content, reflecting the distribution of filler and matrix-fiber adhesion. Although the properties are inferior to those of conventional building materials, the results are within the application-oriented ranges for non-structural temporary formwork (as established by the reported ASTM tests). UV durability associated with carbon black-pigmented caps is presented as a literature-supported hypothesis for future accelerated aging, rather than as a measured outcome. Overall, the findings demonstrate a circular-economy pathway that converts post-consumer plastics and sawmill waste into WPC panels for sustainable construction.
Förderung
- Secretaría de Ciencia, Humanidades, Tecnología e Innovación
- Fondo Sectorial CONAHCYT-SENER Sustentabilidad Energética
- Centro Mexicano de Innovación en Energía Solar
- National Council of Humanities, Science, and Technology CONAHCYT
- National Laboratory of Graphenic Materials
- LANIAUTO
Zitieren
APA
Valencia, J. C. R., Rojas, J. P. B., Araiza, J. L. R., Bueno, J. D. J. P., López, M. L. M., Manzano-Ramírez, A., & Biosca, S. A. O. (2025). Mechanical Performance of Wood–Plastic Composites from Sawdust and Recycled Bottle Cap Polyolefins (PP/HDPE) for Temporary Concrete Formwork. Journal of Composites Science, 9(12), 644. https://doi.org/10.3390/jcs9120644
Vancouver
Valencia JCR, Rojas JPB, Araiza JLR, Bueno JDJP, López MLM, Manzano-Ramírez A, et al. Mechanical Performance of Wood–Plastic Composites from Sawdust and Recycled Bottle Cap Polyolefins (PP/HDPE) for Temporary Concrete Formwork. Journal of Composites Science. 2025;9(12):644. doi:10.3390/jcs9120644
BibTeX
@article{Valencia2025,
author = {Valencia, José Carlos Rosas and Rojas, José Pablo Balderas and Araiza, José Luis Reyes and Bueno, José de Jesús Pérez and López, Maria Luisa Mendoza and Manzano-Ramírez, Alejandro and Biosca, Saúl Antonio Obregón},
title = {Mechanical Performance of Wood–Plastic Composites from Sawdust and Recycled Bottle Cap Polyolefins (PP/HDPE) for Temporary Concrete Formwork},
journal = {Journal of Composites Science},
year = {2025},
volume = {9},
number = {12},
pages = {644},
doi = {10.3390/jcs9120644}
}
EUVIMED