EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Complete-Perforation Response of Hybrid Flax/Aramid–Epoxy Laminates Manufactured by Different Routes and Strike-Face Configurations

Thomaz Jacintho Lopes, Douglas Santos Silva, Raí Felipe Pereira Junio, Lucas de Mendonça Neuba, Belayne Zanini Marchi, Sergio Neves Monteiro

Journal of Composites Science · 29.10.2026 · 10 (11) · 579

DOI: 10.3390/jcs10110579 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Composites Science, online erschienen am 29.10.2026. Verfasst von Thomaz Jacintho Lopes und 5 weiteren Autor:innen. Die Arbeit nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Council for Scientific and Technological Development, Brazilian Council of Scientific Research, Technology and Innovation Development.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study compares the complete-perforation response of flax/aramid–epoxy laminates manufactured with a fixed nominal 12-layer hybrid architecture while varying the manufacturing route and the reinforcement placed at the strike face. Laminates containing six flax and six aramid bidirectional fabric layers arranged in alternating two-layer blocks were produced by manual compression molding or vacuum-assisted hand lay-up and impacted with 9 mm full-metal-jacket projectiles. Five impacts were performed on one panel for each of four configurations; the shots were therefore treated as repeated observations within each panel rather than independent manufacturing replicates. Mean residual velocities ranged from 353.4 to 361.2 m/s, while mean projectile kinetic-energy losses ranged from 213.3 to 237.8 J. The VL panel (vacuum processed, flax strike face) showed the lowest mean residual velocity (353.4 m/s), whereas PA (compression molded, aramid strike face) showed the highest mean projectile kinetic-energy loss (237.8 J), closely followed by VL (236.0 J). Using the measured full-panel masses, mean SEA ranged from 0.970 kJ kg−1 for PA to 1.128 kJ kg−1 for VL. Post-impact inspection showed configuration-dependent visible surface-damage morphologies and projected damage-envelope areas; microscopic failure modes and internal delamination were not measured and are therefore not assigned from the photographs alone. Because every projectile completely perforated the targets, no experimental ballistic-limit velocity (V50) was determined. The results are presented as a descriptive, configuration-resolved comparison of the tested panels; independent panel replication is required for population-level inference on manufacturing-route and strike-face effects.

Förderung

  • National Council for Scientific and Technological Development
  • Brazilian Council of Scientific Research, Technology and Innovation Development

Zitieren

APA

Lopes, T. J., Silva, D. S., Junio, R. F. P., Neuba, L. D. M., Marchi, B. Z., & Monteiro, S. N. (2026). Complete-Perforation Response of Hybrid Flax/Aramid–Epoxy Laminates Manufactured by Different Routes and Strike-Face Configurations. Journal of Composites Science, 10(11), 579. https://doi.org/10.3390/jcs10110579

Vancouver

Lopes TJ, Silva DS, Junio RFP, Neuba LDM, Marchi BZ, Monteiro SN. Complete-Perforation Response of Hybrid Flax/Aramid–Epoxy Laminates Manufactured by Different Routes and Strike-Face Configurations. Journal of Composites Science. 2026;10(11):579. doi:10.3390/jcs10110579

BibTeX
@article{Lopes2026,
  author = {Lopes, Thomaz Jacintho and Silva, Douglas Santos and Junio, Raí Felipe Pereira and Neuba, Lucas de Mendonça and Marchi, Belayne Zanini and Monteiro, Sergio Neves},
  title = {Complete-Perforation Response of Hybrid Flax/Aramid–Epoxy Laminates Manufactured by Different Routes and Strike-Face Configurations},
  journal = {Journal of Composites Science},
  year = {2026},
  volume = {10},
  number = {11},
  pages = {579},
  doi = {10.3390/jcs10110579}
}
Kostenlos starten →