Evaluation of Woven Hemp-Reinforced Polyfurfuryl Alcohol Resin Composites for High-Performance Natural Fibre Composite Applications
Journal of Composites Science · 15.07.2026 · 10 (7) · 372
DOI: 10.3390/jcs10070372 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Composites Science, online erschienen am 15.07.2026. Verfasst von Gilles Koolen und 9 weiteren Autor:innen. Die Arbeit nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Bio-Based Industries Joint Undertaking under the European Union’s Horizon 2020 research and innovation programme.
Abstract (Originalsprache)
The escalating environmental concerns associated with the non-renewable nature of petrochemical-based composite constituents have accelerated the development of sustainable and renewable alternatives. This study evaluates the potential of woven hemp-reinforced polyfurfuryl alcohol (PFA, furan) composites as fully bio-based composite materials. The use of PFA, a fully bio-based resin renowned for its high rigidity and fire-retardant properties, has been hindered by challenges associated with water vapour evolution, acid-catalysed fibre degradation, and porosity formation. Novel woven long hemp fibres were combined with a polyfurfuryl alcohol resin formulated with a mild acid catalyst, while an early-stage venting procedure during compression moulding was investigated to mitigate porosity and fibre degradation. Thermogravimetric analysis was used to determine the venting moments during the moulding cycle. Despite the limited improvement in porosity reduction achieved through the investigated venting strategy, the hemp balanced satin 6/6 fabric–furan composites exhibited commendable stiffness with a maximum modulus of 17.0 ± 0.4 GPa. However, the inherent brittleness of the resin and possibly the presence of fire-retardant fillers limited the tensile strength (a maximum of 71.8 ± 4.2 MPa) and failure strain (a maximum of 0.72 ± 0.07%). The bending properties of neat furan resin produced using an improved curing protocol were comparable to those of conventional thermoset resins, with a modulus of 3.2 ± 0.2 GPa, strength of 110.5 ± 17.3 MPa, and failure strain of 4.1 ± 0.8%. Although several challenges remain, this study demonstrates the potential of natural fibre–furan composites for high-performance natural fibre composite applications and provides guidance for their further development. Future research should focus on optimising venting strategies, avoiding fire retardants to minimise resin brittleness, incorporating matrix tougheners, and enhancing the inherent toughness of the matrix.
Förderung
- Bio-Based Industries Joint Undertaking under the European Union’s Horizon 2020 research and innovation programme
Zitieren
APA
Koolen, G., Madhav, D., Prapavesis, A., Verbruggen, J., Gabrion, X., Gricourt, B., Bottger, W., Lepelaar, M., Placet, V., & Vuure, A. W. V. (2026). Evaluation of Woven Hemp-Reinforced Polyfurfuryl Alcohol Resin Composites for High-Performance Natural Fibre Composite Applications. Journal of Composites Science, 10(7), 372. https://doi.org/10.3390/jcs10070372
Vancouver
Koolen G, Madhav D, Prapavesis A, Verbruggen J, Gabrion X, Gricourt B, et al. Evaluation of Woven Hemp-Reinforced Polyfurfuryl Alcohol Resin Composites for High-Performance Natural Fibre Composite Applications. Journal of Composites Science. 2026;10(7):372. doi:10.3390/jcs10070372
BibTeX
@article{Koolen2026,
author = {Koolen, Gilles and Madhav, Dharmjeet and Prapavesis, Alexandros and Verbruggen, Jens and Gabrion, Xavier and Gricourt, Briac and Bottger, Willem and Lepelaar, Mark and Placet, Vincent and Vuure, Aart W. van},
title = {Evaluation of Woven Hemp-Reinforced Polyfurfuryl Alcohol Resin Composites for High-Performance Natural Fibre Composite Applications},
journal = {Journal of Composites Science},
year = {2026},
volume = {10},
number = {7},
pages = {372},
doi = {10.3390/jcs10070372}
}
EUVIMED