EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Seismic Torsional Behavior of Step-Terrace Mountain Isolated Structures with Isolation-Layer Eccentricity: Shaking Table Tests

Zhanjing Wu, Zhong Tao, Longfei Zhang, Zhengjia Wu, Qiang Huang, Haisu Sun

Infrastructures · 01.06.2026 · 11 (6) · 187

DOI: 10.3390/infrastructures11060187 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Infrastructures, online erschienen am 01.06.2026. Verfasst von Zhanjing Wu und 5 weiteren Autor:innen. Die Arbeit nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To investigate the influence of isolation-layer eccentricity on the torsional response of step-terrace mountain (STM) structures, a 1:10 scaled reinforced concrete model was designed and tested using shaking table experiments. Both isolated and non-isolated configurations were considered, and different eccentricity levels were achieved by adjusting the bearing layouts in the upper and lower isolation layers. The torsional response was evaluated in terms of torsional angle, torsional displacement ratio, and relative torsional effect. The results indicate that the non-isolated STM structure exhibits pronounced torsional amplification and progressive damage accumulation. Deformation and damage are concentrated in the upper stories and dropped-story region, eventually leading to a stiffness–degradation–dominated failure pattern. In contrast, the STM isolated structure effectively suppresses torsional response, and inter-story rotations remain small and relatively uniform along the height, indicating that seismic deformation is primarily redistributed within the isolation layers rather than amplified in the superstructure. The experimental results further demonstrate that torsional behavior is governed by the coupling effect between isolation-layer eccentricity and seismic input direction. The eccentricity in the upper isolation layer plays the dominant role in triggering torsional amplification, while simultaneous eccentricities in both isolation layers produce a cumulative torsional effect. When the eccentricity of the isolation layers is controlled within 5%, the torsional displacement ratio remains below 1.2, while the non-isolated structure reaches values exceeding the code limit of 1.5. In addition, slope-direction excitation intensifies absolute torsional deformation due to overturning effects induced by elevation differences. These findings highlight that torsional response in STM isolated systems is controlled by the interaction between vertical irregularity and isolation-system asymmetry.

Zitieren

APA

Wu, Z., Tao, Z., Zhang, L., Wu, Z., Huang, Q., & Sun, H. (2026). Seismic Torsional Behavior of Step-Terrace Mountain Isolated Structures with Isolation-Layer Eccentricity: Shaking Table Tests. Infrastructures, 11(6), 187. https://doi.org/10.3390/infrastructures11060187

Vancouver

Wu Z, Tao Z, Zhang L, Wu Z, Huang Q, Sun H. Seismic Torsional Behavior of Step-Terrace Mountain Isolated Structures with Isolation-Layer Eccentricity: Shaking Table Tests. Infrastructures. 2026;11(6):187. doi:10.3390/infrastructures11060187

BibTeX
@article{Wu2026,
  author = {Wu, Zhanjing and Tao, Zhong and Zhang, Longfei and Wu, Zhengjia and Huang, Qiang and Sun, Haisu},
  title = {Seismic Torsional Behavior of Step-Terrace Mountain Isolated Structures with Isolation-Layer Eccentricity: Shaking Table Tests},
  journal = {Infrastructures},
  year = {2026},
  volume = {11},
  number = {6},
  pages = {187},
  doi = {10.3390/infrastructures11060187}
}
Kostenlos starten →