Feasibility of Ti-6Al-4V Alloys with Nanoporous and Nanotubular Surfaces for the Treatment of Femoral Defects
International Journal of Molecular Sciences · 2026
DOI: 10.3390/ijms27104335 ↗Kurz gefasst
Fachartikel in der Zeitschrift International Journal of Molecular Sciences, 2026. Verfasst von Daniel Alves Dos Santos und 11 weiteren Autor:innen. Beteiligte Einrichtung: Postgraduate Program in Health Sciences, Faculty of Medicine of Jundiaí (FMJ), Jundiaí 13202-550, Brazil. Hauptthemen laut MEDLINE: Titanium, Femur, Nanopores, Nanotubes. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 98 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Council for Scientific and Technological Development.
Abstract (Originalsprache)
Treating fractures involving complex bone defects remains a major challenge in regenerative medicine. Additive manufacturing enables the fabrication of patient-specific implants, while surface anodization may enhance osseointegration by improving cell adhesion at the bone–implant interface. This study evaluated the feasibility of porous Ti-6Al-4V implants produced by additive manufacturing and surface-modified by anodization for repairing critical-sized femoral defects. Eighty rats were assigned to four groups: control (no graft), non-anodized Ti-6Al-4V implants, nanoporous implants, and nanotubular implants. After six weeks, bone regeneration and mechanical performance were assessed. Newly formed bone volume was significantly higher in the implanted groups compared to control (24.62 ± 3.11%), reaching 47.25 ± 3.92% (non-anodized), 58.20 ± 5.39% (nanoporous), and 40.72 ± 2.22% (nanotubular). Bone strength was also greater in implanted groups (150.27 ± 2.94 N, 151.98 ± 10.37 N, and 156.59 ± 4.95 N, respectively) compared to control (128.16 ± 2.17 N), with no significant differences among treated groups. No signs of implant rejection or inflammation were observed, indicating good biocompatibility. Anodized surfaces demonstrated enhanced osteogenic performance, particularly in the nanoporous group. These findings indicate that anodized porous Ti-6Al-4V implants produced by additive manufacturing combine biological compatibility with mechanical stability, supporting their potential application in bone reconstruction therapies.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Postgraduate Program in Health Sciences, Faculty of Medicine of Jundiaí (FMJ), Jundiaí 13202-550, Brazil.
- Centro de Tecnologia da Informação Renato Archer, Campinas 13069-901, Brazil.
- Graduate Program in Anatomy of Domestic and Wild Animals, Faculty of Veterinary Medicine and Animal Science, University of Sao Paulo (FMVZ/USP), Sao Paulo 05508-270, Brazil.
- Department of Biological Sciences, Bauru School of Dentistry (FOB/USP), University of Sao Paulo, Bauru 17012-901, Brazil.
- Medical School, University Center of Adamantina (FAI), Adamantina 17800-000, Brazil.
- Department of Postgraduate, Dentistry School, Faculty of the Midwest Paulista (FACOP), Piratininga 17499-010, Brazil.
ORCID-Profile: Guilherme Arthur Longhitano, Rogerio Leone Buchaim, Daniela Vieira Buchaim, João Paulo Mardegan Issa, Vinicius Barroso Hirota, André Antonio Pelegrine, Arnaldo Rodrigues Santos, Rui Seabra Ferreira Junior, Marcelo Rodrigues da Cunha
Förderung
- National Council for Scientific and Technological Development
Zitieren
APA
Dos Santos, D. A., Longhitano, G. A., Fraga, G. A., Buchaim, R. L., Buchaim, D. V., Issa, J. P. M., Hirota, V. B., Paulini, M. R., Pelegrine, A. A., Santos, A. R., Ferreira Junior, R. S., & da Cunha, M. R. (2026). Feasibility of Ti-6Al-4V Alloys with Nanoporous and Nanotubular Surfaces for the Treatment of Femoral Defects. International Journal of Molecular Sciences. https://doi.org/10.3390/ijms27104335
Vancouver
Dos Santos DA, Longhitano GA, Fraga GA, Buchaim RL, Buchaim DV, Issa JPM, et al. Feasibility of Ti-6Al-4V Alloys with Nanoporous and Nanotubular Surfaces for the Treatment of Femoral Defects. International Journal of Molecular Sciences. 2026. doi:10.3390/ijms27104335
BibTeX
@article{DosSantos2026,
author = {Dos Santos, Daniel Alves and Longhitano, Guilherme Arthur and Fraga, Gustavo Andrade and Buchaim, Rogerio Leone and Buchaim, Daniela Vieira and Issa, João Paulo Mardegan and Hirota, Vinicius Barroso and Paulini, Marina Ribeiro and Pelegrine, André Antonio and Santos, Arnaldo Rodrigues and Ferreira Junior, Rui Seabra and da Cunha, Marcelo Rodrigues},
title = {Feasibility of Ti-6Al-4V Alloys with Nanoporous and Nanotubular Surfaces for the Treatment of Femoral Defects},
journal = {International Journal of Molecular Sciences},
year = {2026},
doi = {10.3390/ijms27104335}
}
EUVIMED