EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Tracking the Progress of Biocomposites Based on Poly(3-hydroxybutyrate) with Hypromellose Additives via Thermal Analysis, Mechanical Properties, and Biological Studies

Karolina Maternia-Dudzik iD, Łukasz Ożóg iD, Zuzanna Bober iD, Rafał Oliwa iD, Mariusz Oleksy iD, Angelika Kamizela iD, Agnieszka Szyszkowska iD, Katarzyna Rafińska, Weronika Gonciarz iD, Kamil Gancarczyk iD, Anna Czerniecka-Kubicka

International Journal of Molecular Sciences · 2026

DOI: 10.3390/ijms27031596 ↗

Kurz gefasst

Fachartikel in der Zeitschrift International Journal of Molecular Sciences, 2026. Verfasst von Karolina Maternia-Dudzik und 10 weiteren Autor:innen. Beteiligte Einrichtung: Laboratory of Physical Chemistry and Biophysics, Centre for Innovative Research in Medical and Natural Sciences, Faculty of Medicine, University of R…. Hauptthemen laut MEDLINE: Polyesters, Hydroxybutyrates, Biocompatible Materials. Die Arbeit nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Podkarpackie Innovation Center.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Poly(3-hydroxybutyrate) (P3HB) was used to produce biocompatible composites with hypromellose as an additive. The study aimed to assess their biological and mechanical properties, as well as specific thermal parameters and phase content. Differential scanning calorimetry was applied to analyze the phase transitions of both biocomposites and the polymer matrix. Furthermore, the thermal parameters—encompassing both non-equilibrium and equilibrium states—of the biocomposites and unfilled P3HB were evaluated according to their thermal history. Using equilibrium parameters such as the heat of fusion for fully crystalline materials and the heat capacity change at the glass transition for fully amorphous composites, we estimated the degrees of crystallinity as well as the mobile and rigid amorphous fractions. Adding hypromellose to the P3HB matrix reduced crystallinity compared to the unfilled material. At the same time, an increase in the amorphous phase was observed. It was also discovered that the rigid amorphous fraction exists solely in biocomposites containing 2% by mass of filler. Thermogravimetric analysis showed that the thermal stability of all biocomposites surpasses that of unfilled P3HB. Adding an extra 1% filler by mass raises the degradation temperature by about 37 °C compared to unfilled P3HB. The immunosafety of the tested biocomposites, with very low or no endotoxin contamination, was confirmed in accordance with Food and Drug Administration and European Medicines Agency guidelines. The study clearly demonstrates the influence of the filler in the P3HB matrix on various structural, thermal, mechanical, and biological properties of the prepared biocomposites.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

PolyestersHydroxybutyratesBiocompatible MaterialsPolyhydroxybutyratesCalorimetry, Differential ScanningThermogravimetryMaterials TestingAnimalsTemperaturePhase Transition

Stichwörter der Autor:innen

biocompatible materialsbiocompositehypromellosepoly(3-hydroxybutyrate)

Substanzen

PolyestersHydroxybutyratesBiocompatible MaterialsPolyhydroxybutyratespoly-beta-hydroxybutyrate

Autor:innen und Institutionen

  • Laboratory of Physical Chemistry and Biophysics, Centre for Innovative Research in Medical and Natural Sciences, Faculty of Medicine, University of Rzeszow, 35-959 Rzeszow, Poland.
  • Department of Pharmaceutical Technology and Medical Physics, Faculty of Medicine, University of Rzeszow, 35-959 Rzeszow, Poland.
  • Department of Polymer Composites, Faculty of Chemistry, Rzeszow University of Technology, 35-959 Rzeszow, Poland.
  • Provincial Hospital in Kielce, 25-736 Kielce, Poland.
  • Department of Environmental Chemistry and Bioanalytics, Faculty of Chemistry, Nicolaus Copernicus University in Torun, 87-100 Torun, Poland.
  • Department of Immunology and Infectious Biology, Institute of Microbiology, Biotechnology and Immunology, Faculty of Biology and Environmental Protection, University of Lodz, 90-237 Lodz, Poland.

ORCID-Profile: Karolina Maternia-Dudzik, Łukasz Ożóg, Zuzanna Bober, Rafał Oliwa, Mariusz Oleksy, Angelika Kamizela, Agnieszka Szyszkowska, Weronika Gonciarz, Kamil Gancarczyk

Förderung

  • Podkarpackie Innovation Center

Zitieren

APA

Maternia-Dudzik, K., Ożóg, Ł., Bober, Z., Oliwa, R., Oleksy, M., Kamizela, A., Szyszkowska, A., Rafińska, K., Gonciarz, W., Gancarczyk, K., & Czerniecka-Kubicka, A. (2026). Tracking the Progress of Biocomposites Based on Poly(3-hydroxybutyrate) with Hypromellose Additives via Thermal Analysis, Mechanical Properties, and Biological Studies. International Journal of Molecular Sciences. https://doi.org/10.3390/ijms27031596

Vancouver

Maternia-Dudzik K, Ożóg Ł, Bober Z, Oliwa R, Oleksy M, Kamizela A, et al. Tracking the Progress of Biocomposites Based on Poly(3-hydroxybutyrate) with Hypromellose Additives via Thermal Analysis, Mechanical Properties, and Biological Studies. International Journal of Molecular Sciences. 2026. doi:10.3390/ijms27031596

BibTeX
@article{MaterniaDudzik2026,
  author = {Maternia-Dudzik, Karolina and Ożóg, Łukasz and Bober, Zuzanna and Oliwa, Rafał and Oleksy, Mariusz and Kamizela, Angelika and Szyszkowska, Agnieszka and Rafińska, Katarzyna and Gonciarz, Weronika and Gancarczyk, Kamil and Czerniecka-Kubicka, Anna},
  title = {Tracking the Progress of Biocomposites Based on Poly(3-hydroxybutyrate) with Hypromellose Additives via Thermal Analysis, Mechanical Properties, and Biological Studies},
  journal = {International Journal of Molecular Sciences},
  year = {2026},
  doi = {10.3390/ijms27031596}
}
Kostenlos starten →