EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Modification of Polylactide with Triblock and Diblock Copolymers of Ethylene Glycol and Propylene Glycol

Miroslaw Pluta iD, Joanna Bojda iD, Ewa Piorkowska iD

International Journal of Molecular Sciences · 2025

DOI: 10.3390/ijms262110422 ↗

Kurz gefasst

Fachartikel in der Zeitschrift International Journal of Molecular Sciences, 2025. Verfasst von Miroslaw Pluta und 2 weiteren Autor:innen. Beteiligte Einrichtung: Centre of Molecular and Macromolecular Studies, Polish Academy of Sciences, Sienkiewicza 112, 90-363 Lodz, Poland. Hauptthemen laut MEDLINE: Polyesters, Ethylene Glycol, Propylene Glycol, Polymers. Die Arbeit nennt 65 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Centre of Molecular and Macromolecular Studies Polish Academy of Sciences, Centre of Molecular and Macromolecular Studies, Polish Academy of Sciences.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Polylactide (PLA) was melt blended with block copolymers of ethylene glycol and propylene glycol: a triblock copolymer (PPG-b-PEG-b-PPG) with a molar mass of 2700 g/mol and 40 wt% PEG content, and a diblock copolymer (PPG-b-PEG) with a molar mass of 4000 g/mol and 50 wt% PEG content. The structure as well as the thermal and mechanical properties of both amorphous and crystallized blends were investigated. Due to the copolymers’ chemical composition and the resulting phase structure, the 10 wt% amorphous blends with PPG-b-PEG-b-PPG and PPG-b-PEG, with Tg values of 38 °C and 46 °C, respectively, exhibited relatively high yield stress, close to 45 MPa, along with remarkable elongation at break. Notably, the blend with the triblock copolymer showed a 70-fold increase in elongation at break compared to neat amorphous PLA. Furthermore, the tensile impact strength of the blend with the diblock copolymer surpassed that of neat PLA. Upon crystallization, the 10 wt% blends showed reduced yield stress and elongation at break; however, the elongation at break exceeded 7–25 times that of neat crystalline PLA. Furthermore, their tensile impact strength increased to more than three times the value of crystalline PLA.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

PolyestersEthylene GlycolPropylene GlycolPolymersPolyethylene GlycolsTensile StrengthCrystallization

Stichwörter der Autor:innen

PPG-b-PEGPPG-b-PEG-b-PPGblock copolymersplasticizationpolylactide

Substanzen

Polyesterspoly(lactide)Ethylene GlycolPropylene GlycolPolymersPolyethylene Glycols

Autor:innen und Institutionen

  • Centre of Molecular and Macromolecular Studies, Polish Academy of Sciences, Sienkiewicza 112, 90-363 Lodz, Poland.

ORCID-Profile: Miroslaw Pluta, Joanna Bojda, Ewa Piorkowska

Förderung

  • Centre of Molecular and Macromolecular Studies Polish Academy of Sciences
  • Centre of Molecular and Macromolecular Studies, Polish Academy of Sciences

Zitieren

APA

Pluta, M., Bojda, J., & Piorkowska, E. (2025). Modification of Polylactide with Triblock and Diblock Copolymers of Ethylene Glycol and Propylene Glycol. International Journal of Molecular Sciences. https://doi.org/10.3390/ijms262110422

Vancouver

Pluta M, Bojda J, Piorkowska E. Modification of Polylactide with Triblock and Diblock Copolymers of Ethylene Glycol and Propylene Glycol. International Journal of Molecular Sciences. 2025. doi:10.3390/ijms262110422

BibTeX
@article{Pluta2025,
  author = {Pluta, Miroslaw and Bojda, Joanna and Piorkowska, Ewa},
  title = {Modification of Polylactide with Triblock and Diblock Copolymers of Ethylene Glycol and Propylene Glycol},
  journal = {International Journal of Molecular Sciences},
  year = {2025},
  doi = {10.3390/ijms262110422}
}
Kostenlos starten →