Surface Modification of Polylactic Acid Bioscaffold Fabricated via 3D Printing for Craniofacial Bone Tissue Engineering
International Journal of Molecular Sciences · 2023
DOI: 10.3390/ijms242417410 ↗Kurz gefasst
Fachartikel in der Zeitschrift International Journal of Molecular Sciences, 2023. Verfasst von Yao-Chang Liu und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Plastic and Reconstructive Surgery, Keelung Chang Gung Memorial Hospital, Keelung 204, Taiwan. Hauptthemen laut MEDLINE: Tissue Engineering, Osteogenesis. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 68 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Chang Gung Memorial Hospital, Optimizing stem cells combined with 3D printing scaffolds to reconstruct traumatic skull defects.
Abstract (Originalsprache)
Bone tissue engineering is a promising solution for advanced bone defect reconstruction after severe trauma. In bone tissue engineering, scaffolds in three-dimensional (3D) structures are crucial components for cell growth, migration, and infiltration. The three-dimensional printing technique is well suited to manufacturing scaffolds since it can fabricate scaffolds with highly complex designs under good internal structural control. In the current study, the 3D printing technique was utilized to produce polylactic acid (PLA) scaffolds. BMSCs were seeded onto selected scaffolds, either hydrogel-mixed or not, and cultivated in vitro to investigate the osteogenic potential in each group. After osteogenic incubation in vitro, BMSC-seeded scaffolds were implanted onto rat cranium defects, and bone regeneration was observed after 12 weeks. Our results demonstrated that BMSCs were able to seed onto 3D-printed PLA scaffolds under high-resolution observation. Real-time PCR analysis showed their osteogenic ability, which could be further improved after BMSCs were mixed with hydrogel. The in vivo study showed significantly increased bone regeneration when rats’ cranium defects were implanted with a hydrogel-mixed BMSC-seeded scaffold compared to the control and those without cell or hydrogel groups. This study showed that 3D-printed PLA scaffolds are a feasible option for BMSC cultivation and osteogenic differentiation. After mixing with hydrogel, BMSC-seeded 3D-printed scaffolds can facilitate bone regeneration.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Plastic and Reconstructive Surgery, Keelung Chang Gung Memorial Hospital, Keelung 204, Taiwan.
- Division of Trauma Plastic Surgery, Department of Plastic and Reconstructive Surgery, Chang Gung Memorial Hospital at Linkou, Craniofacial Research Center at Taoyuan, College of Medicine, Chang Gung University, Taoyuan…
Förderung
- Chang Gung Memorial Hospital
- Optimizing stem cells combined with 3D printing scaffolds to reconstruct traumatic skull defects
Zitieren
APA
Liu, Y. C., Lo, G. J., Shyu, V. B., Tsai, C. H., Chen, C. H., & Chen, C. T. (2023). Surface Modification of Polylactic Acid Bioscaffold Fabricated via 3D Printing for Craniofacial Bone Tissue Engineering. International Journal of Molecular Sciences. https://doi.org/10.3390/ijms242417410
Vancouver
Liu YC, Lo GJ, Shyu VB, Tsai CH, Chen CH, Chen CT. Surface Modification of Polylactic Acid Bioscaffold Fabricated via 3D Printing for Craniofacial Bone Tissue Engineering. International Journal of Molecular Sciences. 2023. doi:10.3390/ijms242417410
BibTeX
@article{Liu2023,
author = {Liu, Yao-Chang and Lo, Guan-Jie and Shyu, Victor Bong-Hang and Tsai, Chia-Hsuan and Chen, Chih-Hao and Chen, Chien-Tzung},
title = {Surface Modification of Polylactic Acid Bioscaffold Fabricated via 3D Printing for Craniofacial Bone Tissue Engineering},
journal = {International Journal of Molecular Sciences},
year = {2023},
doi = {10.3390/ijms242417410}
}
EUVIMED