Investigating the Properties and Characterization of a Hybrid 3D Printed Antimicrobial Composite Material Using FFF Process: Innovative and Swift
International Journal of Molecular Sciences · 2023
DOI: 10.3390/ijms24108895 ↗Kurz gefasst
Fachartikel in der Zeitschrift International Journal of Molecular Sciences, 2023. Verfasst von Waleed Ahmed und 6 weiteren Autor:innen. Beteiligte Einrichtung: Engineering Requirements Unit, College of Engineering, United Arab Emirates University, Al Ain P.O. Box 15551, United Arab Emirates. Hauptthemen laut MEDLINE: Anti-Bacterial Agents, Anti-Infective Agents. Die Arbeit wurde bisher 22-mal zitiert (Crossref) und nennt 75 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: UAE University, 12R109-Research Center.
Abstract (Originalsprache)
Novel strategies and materials have gained the attention of researchers due to the current pandemic, the global market high competition, and the resistance of pathogens against conventional materials. There is a dire need to develop cost-effective, environmentally friendly, and biodegradable materials to fight against bacteria using novel approaches and composites. Fused filament fabrication (FFF), also known as fused deposition modeling (FDM), is the most effective and novel fabrication method to develop these composites due to its various advantages. Compared to metallic particles alone, composites of different metallic particles have shown excellent antimicrobial properties against common Gram-positive and Gram-negative bacteria. This study investigates the antimicrobial properties of two sets of hybrid composite materials, i.e., Cu-PLA-SS and Cu-PLA-Al, are made using copper-enriched polylactide composite, one-time printed side by-side with stainless steel/PLA composite, and second-time with aluminum/PLA composite respectively. These materials have 90 wt.% of copper, 85 wt.% of SS 17-4, 65 wt.% of Al with a density of 4.7 g/cc, 3.0 g/cc, and 1.54 g/cc, respectively, and were fabricated side by side using the fused filament fabrication (FFF) printing technique. The prepared materials were tested against Gram-positive and Gram-negative bacteria such as Escherichia coli (E. coli), Staphylococcus aureus (S. aureus), Pseudomonas aeruginosa (P. aeruginosa), Salmonella Poona (S. Poona), and Enterococci during different time intervals (5 min, 10 min, 20 min, 1 h, 8 h, and 24 h). The results revealed that both samples showed excellent antimicrobial efficiency, and 99% reduction was observed after 10 min. Hence, three-dimensional (3D) printed polymeric composites enriched with metallic particles can be utilized for biomedical, food packaging, and tissue engineering applications. These composite materials can also provide sustainable solutions in public places and hospitals where the chances of touching surfaces are higher.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Engineering Requirements Unit, College of Engineering, United Arab Emirates University, Al Ain P.O. Box 15551, United Arab Emirates.
- Department of Chemical and Petroleum Engineering, College of Engineering, United Arab Emirates University, Al Ain P.O. Box 15551, United Arab Emirates.
- Department of Microbiology & Immunology, College of Medicine & Health Sciences, United Arab Emirates University, Al Ain P.O. Box 15551, United Arab Emirates.
- Zayed Center for Health Sciences, United Arab Emirates University, Al Ain P.O. Box 15551, United Arab Emirates.
- Department of Civil and Environmental Engineering, College of Engineering, United Arab Emirates University, Al Ain P.O. Box 15551, United Arab Emirates.
- Department of Mechanical Engineering, College of Engineering, United Arab Emirates University, Al Ain P.O. Box 15551, United Arab Emirates.
ORCID-Profile: Waleed Ahmed, Ali H Al-Marzouqi, Muhammad Hamza Nazir, Essam Zaneldin, Mushtaq Khan
Förderung
- UAE University
- 12R109-Research Center
Zitieren
APA
Ahmed, W., Al-Marzouqi, A. H., Nazir, M. H., Rizvi, T. A., Zaneldin, E., Khan, M., & Aziz, M. (2023). Investigating the Properties and Characterization of a Hybrid 3D Printed Antimicrobial Composite Material Using FFF Process: Innovative and Swift. International Journal of Molecular Sciences. https://doi.org/10.3390/ijms24108895
Vancouver
Ahmed W, Al-Marzouqi AH, Nazir MH, Rizvi TA, Zaneldin E, Khan M, et al. Investigating the Properties and Characterization of a Hybrid 3D Printed Antimicrobial Composite Material Using FFF Process: Innovative and Swift. International Journal of Molecular Sciences. 2023. doi:10.3390/ijms24108895
BibTeX
@article{Ahmed2023,
author = {Ahmed, Waleed and Al-Marzouqi, Ali H and Nazir, Muhammad Hamza and Rizvi, Tahir A and Zaneldin, Essam and Khan, Mushtaq and Aziz, Muthanna},
title = {Investigating the Properties and Characterization of a Hybrid 3D Printed Antimicrobial Composite Material Using FFF Process: Innovative and Swift},
journal = {International Journal of Molecular Sciences},
year = {2023},
doi = {10.3390/ijms24108895}
}
EUVIMED