EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Vat Photopolymerization 3D Printing of Hydrogels with Re-Adjustable Swelling

Pedro Liz-Basteiro iD, Felipe Reviriego, Enrique Martínez-Campos, Helmut Reinecke, Carlos Elvira, Juan Rodríguez-Hernández, Alberto Gallardo

Gels · 25.07.2023 · 9 (8) · 600

DOI: 10.3390/gels9080600 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Gels, online erschienen am 25.07.2023. Verfasst von Pedro Liz-Basteiro und 6 weiteren Autor:innen. Beteiligte Einrichtung: Instituto de Ciencia y Tecnología de Polímeros (ICTP), CSIC, C/Juan de la Cierva 3, 28006 Madrid, Spain. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministerio de Ciencia, Innovación y Universidades,, Ministerio de Ciencia, Innovación y Universidades.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Vat photopolymerization typically prints highly crosslinked networks. Printing hydrogels, which are also networks but with a high swelling capacity in water and therefore with low crosslinking density, is a challenge for this technique. However, it may be of interest in medicine and in other areas, since it would allow for the preparation of this type of 3D-shaped material. In this work, an approach for printing hydrogels via vat photopolymerization that uses a mixture of stable and hydrolysable crosslinkers has been evaluated so that an initial highly crosslinked network can be printed, although after hydrolysis it becomes a network with low crosslinking. This approach has been studied with PEO/PEG-related formulations, that is, with a PEG-dimethacrylate as a stable crosslinker, a PEO-related derivative carrying β-aminoesters as a degradable crosslinker, and PEG-methyl ether acrylate and hydroxyethyl acrylate as monofunctional monomers. A wide family of formulations has been studied, maintaining the weight percentage of the crosslinkers at 15%. Resins have been studied in terms of viscosity, and the printing process has been evaluated through the generation of Jacobs working curves. It has been shown that this approach allows for the printing of pieces of different shapes and sizes via vat photopolymerization, and that these pieces can re-ajust their water content in a tailored fashion through treatments in different media (PBS or pH 10 buffer).

Schlagwörter

Stichwörter der Autor:innen

3D printingDLPUV curingadditive manufacturinghydrogelhydrolysable crosslinkerre-adjustable swellingvat polymerization

Autor:innen und Institutionen

  • Instituto de Ciencia y Tecnología de Polímeros (ICTP), CSIC, C/Juan de la Cierva 3, 28006 Madrid, Spain.
  • Grupo de Síntesis Orgánica y Bioevaluación, Instituto Pluridisciplinar (IP), UCM, Unidad Asociada al CSIC por el ICTP y el IQM, Paseo de Juan XXIII 1, 28040 Madrid, Spain.

ORCID-Profile: Pedro Liz-Basteiro

Förderung

  • Ministerio de Ciencia, Innovación y Universidades,
  • Ministerio de Ciencia, Innovación y Universidades

Zitieren

APA

Liz-Basteiro, P., Reviriego, F., Martínez-Campos, E., Reinecke, H., Elvira, C., Rodríguez-Hernández, J., & Gallardo, A. (2023). Vat Photopolymerization 3D Printing of Hydrogels with Re-Adjustable Swelling. Gels, 9(8), 600. https://doi.org/10.3390/gels9080600

Vancouver

Liz-Basteiro P, Reviriego F, Martínez-Campos E, Reinecke H, Elvira C, Rodríguez-Hernández J, et al. Vat Photopolymerization 3D Printing of Hydrogels with Re-Adjustable Swelling. Gels. 2023;9(8):600. doi:10.3390/gels9080600

BibTeX
@article{LizBasteiro2023,
  author = {Liz-Basteiro, Pedro and Reviriego, Felipe and Martínez-Campos, Enrique and Reinecke, Helmut and Elvira, Carlos and Rodríguez-Hernández, Juan and Gallardo, Alberto},
  title = {Vat Photopolymerization 3D Printing of Hydrogels with Re-Adjustable Swelling},
  journal = {Gels},
  year = {2023},
  volume = {9},
  number = {8},
  pages = {600},
  doi = {10.3390/gels9080600}
}
Kostenlos starten →