EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Multifunctional 3D-Printed Alginate Emulgel Patches Incorporating Plant Extracts for Potential Burn Wound Applications

Roxana Colette Sandulovici iD, Ion Mircioiu, Mariana Panțuroiu iD, Corneliu Dan Blendea, Mirela Claudia Rîmbu iD, Daniel Cord, Carmen Elisabeta Manea iD, Carmen Marinela Mihăilescu iD, Mirela Antonela Mihăilă iD, Iulian Sârbu iD, Horia Sebastian Iliescu, Manuel Ovidiu Amzoiu und 5 weitere

Gels · 17.06.2026 · 12 (6) · 541

DOI: 10.3390/gels12060541 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Gels, online erschienen am 17.06.2026. Verfasst von Roxana Colette Sandulovici und 16 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Pharmacy, Titu Maiorescu University, 040314 Bucharest, Romania. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 92 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Multifunctional dressings capable of maintaining a moist environment, supporting tissue regeneration, and delivering bioactive compounds are increasingly being explored as promising strategies for burn wound management. In this study, alginate-based emulgel patches incorporating hydrophilic and lipophilic plant extracts were developed by extrusion-based 3D printing as potential topical systems for burn wound applications. The formulation included sodium alginate, hyaluronic acid, and hydroglyceric extracts of Calendula officinalis, Matricaria chamomilla, and Plantago major, as well as oily extracts of Hippophae rhamnoides and Hypericum perforatum. The emulgel was evaluated for pH, rheological behaviour, spreadability, physical stability, apparent hydrodynamic size distribution, zeta potential, total polyphenol content, and antioxidant activity. Following Ca2+-induced crosslinking, uniform and flexible 3D-printed patches were obtained and further characterised for pharmacotechnical, physicochemical, structural, functional, and biological properties. The emulgel exhibited suitable characteristics for extrusion-based printing, while the resulting patches showed good dimensional uniformity, flexibility, swelling capacity, water vapour transmission, and surface pH compatible with topical application. FTIR, DLS, SEM, and SEM–EDX analyses supported the formation of a Ca2+-crosslinked alginate network and confirmed the presence of structurally heterogeneous domains with homogeneous calcium distribution. The patches retained plant-derived bioactive compounds, with a total polyphenol content of 0.2878 ± 0.016 mg GAE/g hydrated patch, and showed improved antioxidant activity compared with the corresponding emulgel. In vitro release studies indicated the time-dependent diffusion of polyphenols over 24 h, with cumulative release reaching 64.42%. The patches also exhibited a water vapour transmission rate of 1270 ± 93 g/m2/24 h, indicating adequate moisture regulation. HaCaT cell viability remained above 90% at lower tested concentrations, demonstrating a favourable biocompatibility profile. Overall, the developed 3D-printed alginate emulgel patches represent promising multifunctional systems for potential burn wound management and warrant further preclinical investigation.

Schlagwörter

Stichwörter der Autor:innen

3D printingHaCaT cellsalginateantioxidant activityburn wound applicationsburn wound dressingemulgelplant extractspolyphenols

Autor:innen und Institutionen

  • Faculty of Pharmacy, Titu Maiorescu University, 040314 Bucharest, Romania.
  • Faculty of Medicine, Titu Maiorescu University, 040314 Bucharest, Romania.
  • Horia Hulubei National Institute for R&D in Physics and Nuclear Engineering (IFIN-HH), Reactorului 30 St., 077125 Magurele, Romania.
  • National Institute for Research and Development in Microtehnologies (IMT), 077190 Bucharest, Romania.
  • Doctoral School, University of Medicine and Pharmacy of Craiova, 200349 Craiova, Romania.
  • Stefan S. Nicolau Institute of Virology, Mihai Bravu St, 030304 Bucharest, Romania.

ORCID-Profile: Roxana Colette Sandulovici, Mariana Panțuroiu, Mirela Claudia Rîmbu, Carmen Elisabeta Manea, Carmen Marinela Mihăilescu, Mirela Antonela Mihăilă, Iulian Sârbu, Adina Boldeiu, Vasilica Țucureanu, Luiza Mădălina Cima, Mona Luciana Gălățanu

Zitieren

APA

Sandulovici, R. C., Mircioiu, I., Panțuroiu, M., Blendea, C. D., Rîmbu, M. C., Cord, D., Manea, C. E., Mihăilescu, C. M., Mihăilă, M. A., Sârbu, I., Iliescu, H. S., Amzoiu, M. O., Boldeiu, A., Țucureanu, V., Brîncoveanu, O., Cima, L. M., & Gălățanu, M. L. (2026). Multifunctional 3D-Printed Alginate Emulgel Patches Incorporating Plant Extracts for Potential Burn Wound Applications. Gels, 12(6), 541. https://doi.org/10.3390/gels12060541

Vancouver

Sandulovici RC, Mircioiu I, Panțuroiu M, Blendea CD, Rîmbu MC, Cord D, et al. Multifunctional 3D-Printed Alginate Emulgel Patches Incorporating Plant Extracts for Potential Burn Wound Applications. Gels. 2026;12(6):541. doi:10.3390/gels12060541

BibTeX
@article{Sandulovici2026,
  author = {Sandulovici, Roxana Colette and Mircioiu, Ion and Panțuroiu, Mariana and Blendea, Corneliu Dan and Rîmbu, Mirela Claudia and Cord, Daniel and Manea, Carmen Elisabeta and Mihăilescu, Carmen Marinela and Mihăilă, Mirela Antonela and Sârbu, Iulian and Iliescu, Horia Sebastian and Amzoiu, Manuel Ovidiu and Boldeiu, Adina and Țucureanu, Vasilica and Brîncoveanu, Oana and Cima, Luiza Mădălina and Gălățanu, Mona Luciana},
  title = {Multifunctional 3D-Printed Alginate Emulgel Patches Incorporating Plant Extracts for Potential Burn Wound Applications},
  journal = {Gels},
  year = {2026},
  volume = {12},
  number = {6},
  pages = {541},
  doi = {10.3390/gels12060541}
}
Kostenlos starten →