EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Multi-Material Extrusion-Based 3D Printing of Hybrid Scaffolds for Tissue Engineering Application

Andrey Abramov, Yan Sulkhanov, Natalia Menshutina iD

Gels · 29.01.2026 · 12 (2) · 123

DOI: 10.3390/gels12020123 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Gels, online erschienen am 29.01.2026. Verfasst von Andrey Abramov und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemical and Pharmaceutical Engineering, Mendeleev University of Chemical Technology of Russia, Miusskaya pl. 9, 125047 Moscow, Russia. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Russian Science Foundation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Additive manufacturing of hydrogel-based scaffolds requires concurrent control of material rheology and extrusion dynamics, especially in multi-material architectures. In this work, we develop a modular multi-material extrusion-based 3D-printing platform that combines a filament-fed extruder for thermoplastic polymers with a piston-driven extruder for viscous gel inks, together with an empirical calibration procedure for gel dosing. The calibration algorithm optimizes the pre-extrusion and retraction displacement (EPr/R) based on stepwise extrusion experiments and reduces the discrepancy between theoretical and measured deposited mass for shear-thinning alginate gels to below the prescribed tolerance. The calibrated system is then used to fabricate two representative hybrid constructs: partially crosslinked sodium alginate scaffolds with an internal hollow channel supported by a removable polycaprolactone framework, and self-supporting structures based on a sodium alginate–chitosan polyelectrolyte complex obtained by sequential co-extrusion. The resulting constructs remain mechanically stable after ionic crosslinking and solvent treatment and can subsequently be converted into highly porous scaffolds by freeze- or supercritical drying. The proposed combination of hardware architecture and extrusion calibration enables reproducible multi-material 3D printing of hydrogel–thermoplastic hybrid scaffolds and can be readily adapted to other gel-based inks for tissue engineering applications.

Schlagwörter

Stichwörter der Autor:innen

direct ink writing (DIW)extrusion-based 3D printinghydrogel inkshydrogel–thermoplastic hybrid scaffoldsmulti-material 3D printingprintability and dosing accuracyprocess parameterstissue engineering

Autor:innen und Institutionen

  • Department of Chemical and Pharmaceutical Engineering, Mendeleev University of Chemical Technology of Russia, Miusskaya pl. 9, 125047 Moscow, Russia.

ORCID-Profile: Natalia Menshutina

Förderung

  • Russian Science Foundation

Zitieren

APA

Abramov, A., Sulkhanov, Y., & Menshutina, N. (2026). Multi-Material Extrusion-Based 3D Printing of Hybrid Scaffolds for Tissue Engineering Application. Gels, 12(2), 123. https://doi.org/10.3390/gels12020123

Vancouver

Abramov A, Sulkhanov Y, Menshutina N. Multi-Material Extrusion-Based 3D Printing of Hybrid Scaffolds for Tissue Engineering Application. Gels. 2026;12(2):123. doi:10.3390/gels12020123

BibTeX
@article{Abramov2026,
  author = {Abramov, Andrey and Sulkhanov, Yan and Menshutina, Natalia},
  title = {Multi-Material Extrusion-Based 3D Printing of Hybrid Scaffolds for Tissue Engineering Application},
  journal = {Gels},
  year = {2026},
  volume = {12},
  number = {2},
  pages = {123},
  doi = {10.3390/gels12020123}
}
Kostenlos starten →