EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Fabrication and Performance Study of 3D-Printed Ceramic-in-Gel Polymer Electrolytes

Xiubing Yao, Wendong Qin, Qiankun Hun, Naiyao Mao, Junming Li, Xinghua Liang, Ying Long, Yifeng Guo

Gels · 10.07.2025 · 11 (7) · 534

DOI: 10.3390/gels11070534 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Gels, online erschienen am 10.07.2025. Verfasst von Xiubing Yao und 7 weiteren Autor:innen. Beteiligte Einrichtung: Guangxi Key Laboratory of Automobile Components and Vehicle Technology, Guangxi University of Science & Technology, Liuzhou 545006, China. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Reginal Collaboration R&D Program of Sichuan Province under Grant, Fund Project of the Guangxi Key R&D Programme Projects, National Natural Science Foundation of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Solid-state electrolytes (SSEs) have emerged as a promising solution for next-generation lithium-ion batteries due to their excellent safety and high energy density. However, their practical application is still hindered by critical challenges such as their low ionic conductivity and high interfacial resistance at room temperature. The innovative application of 3D printing in the field of electrochemistry, particularly in solid-state electrolytes, endows energy storage devices with attractive characteristics. In this study, ceramic-in-gel polymer electrolytes (GPEs) based on PVDF-HFP/PAN@LLZTO were fabricated using a direct ink writing (DIW) 3D printing technique. Under the optimal printing conditions (printing speed of 40 mm/s and fill density of 70%), the printed electrolyte exhibited a uniform and dense sponge-like porous structure, achieving a high ionic conductivity of 5.77 × 10−4 S·cm−1, which effectively facilitated lithium-ion transport. A structural analysis indicated that the LLZTO fillers were uniformly dispersed within the polymer matrix, significantly enhancing the electrochemical stability of the electrolyte. When applied in a LiFePO4|GPEs|Li cell configuration, the electrolyte delivered excellent electrochemical performance, with high initial discharge capacities of 168 mAh·g−1 at 0.1 C and 166 mAh·g−1 at 0.2 C, and retained 92.8% of its capacity after 100 cycles at 0.2 C. This work demonstrates the great potential of 3D printing technology in fabricating high-performance GPEs. It provides a novel strategy for the structural design and industrial scalability of lithium-ion batteries.

Schlagwörter

Stichwörter der Autor:innen

3D printinglithium-ion batteriesporous structure

Autor:innen und Institutionen

  • Guangxi Key Laboratory of Automobile Components and Vehicle Technology, Guangxi University of Science & Technology, Liuzhou 545006, China.
  • Liuzhou Institute of Technology, Liuzhou 545616, China.
  • School of Mechanical Engineering, Chengdu University, Chengdu 610106, China.

Förderung

  • Reginal Collaboration R&D Program of Sichuan Province under Grant
  • Fund Project of the Guangxi Key R&D Programme Projects
  • National Natural Science Foundation of China
  • Guangxi key laboratory of Automobile Components and Vehicle technology
  • Innovation Project of Guangxi Graduate education
  • Ph.D. Programs Foundation of Guangxi University of Science and Technology
  • Regional Collaboration R&D Program of Sichuan Province
  • Fund Project of the Guangxi Key R&D Programme Projects

Zitieren

APA

Yao, X., Qin, W., Hun, Q., Mao, N., Li, J., Liang, X., Long, Y., & Guo, Y. (2025). Fabrication and Performance Study of 3D-Printed Ceramic-in-Gel Polymer Electrolytes. Gels, 11(7), 534. https://doi.org/10.3390/gels11070534

Vancouver

Yao X, Qin W, Hun Q, Mao N, Li J, Liang X, et al. Fabrication and Performance Study of 3D-Printed Ceramic-in-Gel Polymer Electrolytes. Gels. 2025;11(7):534. doi:10.3390/gels11070534

BibTeX
@article{Yao2025,
  author = {Yao, Xiubing and Qin, Wendong and Hun, Qiankun and Mao, Naiyao and Li, Junming and Liang, Xinghua and Long, Ying and Guo, Yifeng},
  title = {Fabrication and Performance Study of 3D-Printed Ceramic-in-Gel Polymer Electrolytes},
  journal = {Gels},
  year = {2025},
  volume = {11},
  number = {7},
  pages = {534},
  doi = {10.3390/gels11070534}
}
Kostenlos starten →