EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

3D Printing Properties of Heat-Induced Sodium Alginate–Whey Protein Isolate Edible Gel

Zhihua Li, Siwen Wang, Zhou Qin, Wenbing Fang, Ziang Guo, Xiaobo Zou

Gels · 27.06.2024 · 10 (7) · 425

DOI: 10.3390/gels10070425 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Gels, online erschienen am 27.06.2024. Verfasst von Zhihua Li und 5 weiteren Autor:innen. Beteiligte Einrichtung: School of Food and Biological Engineering, Jiangsu University, Zhenjiang 212013, China. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the National Key Research and Development Program of China, Natural Science Foundation of Jiangsu Province, National Key Research and Development Program of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The objective of this study was to develop a food 3D printing gel and investigate the effects of whey protein isolate (WPI), sodium alginate (SA), and water-bath heating time on the 3D printing performance of the gel. Initially, the influence of these three factors on the rheological properties of the gel was examined to determine the suitable formulation ranges for 3D printing. Subsequently, the formulation was optimized using response surface methodology, and texture analysis, scanning electron microscopy (SEM), and Fourier-transform infrared (FTIR) spectroscopy were conducted. The rheological results indicated that gels with WPI concentrations of 6–7 g, SA concentrations of 0.8–1.2 g, and water-bath heating times of 10–12 min exhibited lower yield stress and better self-supporting properties. The optimized formulation, determined through response surface methodology, consisted of 1.2 g SA, 6.5 g WPI, and a heating time of 12 min. This optimized formulation demonstrated enhanced extrusion capability and superior printing performance. SEM analysis revealed that the optimized gel possessed good mechanical strength, and FTIR spectroscopy confirmed the successful composite formation of the gel. Overall, the results indicate that the optimized gel formulation can be successfully printed and exhibits excellent 3D printing performance.

Schlagwörter

Stichwörter der Autor:innen

3D printingrheological propertiessodium alginatewhey protein isolate

Autor:innen und Institutionen

  • School of Food and Biological Engineering, Jiangsu University, Zhenjiang 212013, China.

Förderung

  • the National Key Research and Development Program of China
  • Natural Science Foundation of Jiangsu Province
  • National Key Research and Development Program of China
  • National Natural Science Foundation of China
  • Priority Academic Program Development of Jiangsu Higher Education Institutions (PAPD)

Zitieren

APA

Li, Z., Wang, S., Qin, Z., Fang, W., Guo, Z., & Zou, X. (2024). 3D Printing Properties of Heat-Induced Sodium Alginate–Whey Protein Isolate Edible Gel. Gels, 10(7), 425. https://doi.org/10.3390/gels10070425

Vancouver

Li Z, Wang S, Qin Z, Fang W, Guo Z, Zou X. 3D Printing Properties of Heat-Induced Sodium Alginate–Whey Protein Isolate Edible Gel. Gels. 2024;10(7):425. doi:10.3390/gels10070425

BibTeX
@article{Li2024,
  author = {Li, Zhihua and Wang, Siwen and Qin, Zhou and Fang, Wenbing and Guo, Ziang and Zou, Xiaobo},
  title = {3D Printing Properties of Heat-Induced Sodium Alginate–Whey Protein Isolate Edible Gel},
  journal = {Gels},
  year = {2024},
  volume = {10},
  number = {7},
  pages = {425},
  doi = {10.3390/gels10070425}
}
Kostenlos starten →