EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

From Thermal Ablation to Mechanical Fracture: Lightning-Caused Breakage of Insulated Conductors Under Thermal–Mechanical Coupling of Power-Frequency Follow Current Arcs

Xin Ning, Yuan Li, Rui Yu, Longchen Liu, Jiayi Wang, Jingxin Zou, Hao Wang, Jiaxi Liu, Xin Yang, Tian Tan

Eng · 11.11.2026 · 7 (11) · 640

DOI: 10.3390/eng7110640 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Eng, online erschienen am 11.11.2026. Verfasst von Xin Ning und 9 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Natural Science Foundation of Sichuan Province.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Arc erosion induced by lightning-triggered power-frequency follow currents is a primary cause of insulated conductor breakage. However, significant thermal–mechanical differences remain between laboratory low-current tests and field high-current faults, and existing models fail to quantitatively characterize the transition of damage mechanisms under different currents. This study compares the fracture morphologies of two types of broken samples using scanning electron microscopy. The laboratory low-current samples exhibit an oxygen content as high as 41.22% at the fracture surface, accompanied by a reef-like progressive melting morphology, indicating thermal erosion dominance. In contrast, the field high-current samples display extremely low oxygen content, numerous cracks and pores, and pronounced mechanical fracture features. To quantitatively reveal these mechanisms, a magnetohydrodynamic arc ablation model coupled with material phase change was established using a JKLYJ-70 insulated conductor, and simulations were conducted for a typical fault current of 5 kA. Results indicate a maximum arc temperature of 12,974 K. The axial temperature distribution exhibits a “higher-at-ends, lower-in-middle” profile, while the radial temperature distribution approximates a Gaussian distribution. The peak electrodynamic force on the conductor surface reaches 3951 N, significantly exceeding other force components. Theoretical predictions indicate that the breakage time under pure thermal effects is 14.8 s, which is shortened to 2.8 s after incorporating the electrodynamic force, representing a reduction of 81.1%. Further calculations identify a theoretically predicted critical current threshold of approximately 1.45 kA. Above this threshold, the electrodynamic force is dominant, and mechanical fracture occurs prior to melting. Below this threshold, thermal accumulation and melting erosion are dominant, requiring the conductor to reach its melting point before breakage. This threshold reveals the critical condition for the transition from thermal-dominated to force-dominated breakage under thermal–mechanical coupling, providing a general modeling approach for high-temperature arc–conductor interaction analysis and a theoretical basis for differentiated protection design in electrical engineering.

Förderung

  • Natural Science Foundation of Sichuan Province

Zitieren

APA

Ning, X., Li, Y., Yu, R., Liu, L., Wang, J., Zou, J., Wang, H., Liu, J., Yang, X., & Tan, T. (2026). From Thermal Ablation to Mechanical Fracture: Lightning-Caused Breakage of Insulated Conductors Under Thermal–Mechanical Coupling of Power-Frequency Follow Current Arcs. Eng, 7(11), 640. https://doi.org/10.3390/eng7110640

Vancouver

Ning X, Li Y, Yu R, Liu L, Wang J, Zou J, et al. From Thermal Ablation to Mechanical Fracture: Lightning-Caused Breakage of Insulated Conductors Under Thermal–Mechanical Coupling of Power-Frequency Follow Current Arcs. Eng. 2026;7(11):640. doi:10.3390/eng7110640

BibTeX
@article{Ning2026,
  author = {Ning, Xin and Li, Yuan and Yu, Rui and Liu, Longchen and Wang, Jiayi and Zou, Jingxin and Wang, Hao and Liu, Jiaxi and Yang, Xin and Tan, Tian},
  title = {From Thermal Ablation to Mechanical Fracture: Lightning-Caused Breakage of Insulated Conductors Under Thermal–Mechanical Coupling of Power-Frequency Follow Current Arcs},
  journal = {Eng},
  year = {2026},
  volume = {7},
  number = {11},
  pages = {640},
  doi = {10.3390/eng7110640}
}
Kostenlos starten →