EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Biomass Char Injection Position on Combustion and NO Formation in a Tangentially Fired Boiler

Fan Fang, Qi Li, Xiangyu Zhang, Mingdong Li, Liu Liu, Weiping Chen, Xiaohan Ren, Jian Liu

Energies · 11.08.2026 · 19 (16) · 3763

DOI: 10.3390/en19163763 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Energies, online erschienen am 11.08.2026. Verfasst von Fan Fang und 7 weiteren Autor:innen. Die Arbeit nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Research and Development Plan of China, Science and Technology Project of China Huaneng Group.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To clarify the effects of biomass char injection position on combustion characteristics and NO formation, a three-dimensional CFD model of a 300 MW tangentially fired pulverized coal boiler was developed using ANSYS Fluent. The Realizable k-ε model, discrete phase model, species transport model, and P-1 radiation model were employed to describe the flow, combustion, heat transfer, and NO formation processes. The model was validated against field measurements under pure pulverized coal combustion conditions. Based on the validated model, five co-firing cases were designed by injecting biomass char through primary air nozzles located at five different elevations in the burner zone. The results show that biomass char injection position significantly affects furnace flow organization, heat release distribution, carbon conversion, and NO formation, while maintaining the overall tangential swirling structure. Case C achieved the highest outlet velocity of 10.42 m/s, which was 9.1% higher than that of Case E, and exhibited the lowest CO concentration, indicating improved carbon conversion performance. However, the intensified oxidation environment in Case C promoted fuel-N conversion and resulted in the highest NO concentration of 313 ppm. Case B achieved the highest outlet temperature of 1429 K, which was 6.8% higher than that of Case E. In comparison, Case D maintained a similar CO2 mole fraction of 0.1546 to Case C, which was 0.1545, while reducing the NO concentration from 313 ppm in Case C to 145 ppm, corresponding to a reduction of 53.7%. Therefore, Case D achieved the most favorable balance between carbon conversion and NO emission control under the investigated conditions. This study demonstrates that biomass char injection position is an important operational parameter for optimizing biomass utilization and reducing NO emissions in tangentially fired pulverized coal boilers.

Förderung

  • National Research and Development Plan of China
  • Science and Technology Project of China Huaneng Group

Zitieren

APA

Fang, F., Li, Q., Zhang, X., Li, M., Liu, L., Chen, W., Ren, X., & Liu, J. (2026). Effect of Biomass Char Injection Position on Combustion and NO Formation in a Tangentially Fired Boiler. Energies, 19(16), 3763. https://doi.org/10.3390/en19163763

Vancouver

Fang F, Li Q, Zhang X, Li M, Liu L, Chen W, et al. Effect of Biomass Char Injection Position on Combustion and NO Formation in a Tangentially Fired Boiler. Energies. 2026;19(16):3763. doi:10.3390/en19163763

BibTeX
@article{Fang2026,
  author = {Fang, Fan and Li, Qi and Zhang, Xiangyu and Li, Mingdong and Liu, Liu and Chen, Weiping and Ren, Xiaohan and Liu, Jian},
  title = {Effect of Biomass Char Injection Position on Combustion and NO Formation in a Tangentially Fired Boiler},
  journal = {Energies},
  year = {2026},
  volume = {19},
  number = {16},
  pages = {3763},
  doi = {10.3390/en19163763}
}
Kostenlos starten →