Energy-Optimal and Thermally Robust Predictive Flux Control of Industrial Induction Motor Drives
Energies · 31.07.2026 · 19 (15) · 3608
DOI: 10.3390/en19153608 ↗Kurz gefasst
Fachartikel in der Zeitschrift Energies, online erschienen am 31.07.2026. Verfasst von Oybek Kh. Ishnazarov und 4 weiteren Autor:innen. Die Arbeit nennt 18 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Variable-speed induction motor drives spend most of their service life at partial load, where rated-flux field-oriented control (FOC) is inefficient and where loss-minimizing control (LMC) recovers a large part of the loss. LMC, however, is brittle in two ways that matter in industry: it is tuned isothermally, so as the windings heat, the rotor-resistance drift detunes the field orientation and corrupts torque; and it treats the loss-optimal flux as a quasi-static set-point, so an abrupt load rise from a light-load, low-flux condition forces a slow flux rebuild that throttles torque. This paper proposes a thermally adaptive economic model predictive controller (TA-EMPC) that retains the energy optimum of LMC while removing both weaknesses. A temperature-coupled total-loss model (machine copper and core loss plus inverter conduction and switching loss) is minimized over a finite horizon subject to a torque-delivery constraint; a reduced-order two-node thermal observer updates the loss-defining resistances online without a temperature sensor; and a load-demand-aware flux-reservation term pre-magnetizes the machine ahead of anticipated torque rises. In simulations on a representative 7.5 kW drive, TA-EMPC matched the energy of static LMC to within 0.3% across pump, conveyor, and fast-cycling duty profiles—both saving 1.4–2.3% of cycle energy relative to rated-flux FOC, and up to about 14.7 efficiency points at very light load—while, unlike LMC, holding the steady torque error below 0.5% when the winding temperature rose by about 95 °C, to a hot steady state near 115 °C (a stator-resistance increase of roughly 37%) (against an 8% error for the non-adaptive scheme) and reducing the torque undershoot during a light-to-heavy load step from about 23% to near zero. All quantitative results reported in this work are obtained entirely in simulation. A per-step operation-count analysis—not an on-target timing measurement—indicates that the condensed quadratic-program formulation with move blocking is executable within the 100 µs sampling interval on a production digital signal controller for the chosen control horizon; experimental validation on a loaded dynamometer bench, together with on-target timing measurement, is identified as future work. The contribution is thus energy-efficient operation delivered with the torque robustness that loss minimization alone does not provide.
Zitieren
APA
Ishnazarov, O. K., Khoshimov, U. K., Nabiyev, M. B., Kurvonboev, B. I., & Abdullayev, J. N. (2026). Energy-Optimal and Thermally Robust Predictive Flux Control of Industrial Induction Motor Drives. Energies, 19(15), 3608. https://doi.org/10.3390/en19153608
Vancouver
Ishnazarov OK, Khoshimov UK, Nabiyev MB, Kurvonboev BI, Abdullayev JN. Energy-Optimal and Thermally Robust Predictive Flux Control of Industrial Induction Motor Drives. Energies. 2026;19(15):3608. doi:10.3390/en19153608
BibTeX
@article{Ishnazarov2026,
author = {Ishnazarov, Oybek Kh. and Khoshimov, Ural Kh. and Nabiyev, Muslimbek B. and Kurvonboev, Botirjon I. and Abdullayev, Jamoldin N.},
title = {Energy-Optimal and Thermally Robust Predictive Flux Control of Industrial Induction Motor Drives},
journal = {Energies},
year = {2026},
volume = {19},
number = {15},
pages = {3608},
doi = {10.3390/en19153608}
}
EUVIMED