EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Characteristics of Deep Coal Reservoir and Key Control Factors of Coalbed Methane Accumulation in Linxing Area

Chuanqi Tao, Yong Li, Yanbin Wang, Xiaoming Ni, Xiang Wu, Shihu Zhao

Energies · 21.08.2023 · 16 (16) · 6085

DOI: 10.3390/en16166085 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Energies, online erschienen am 21.08.2023. Verfasst von Chuanqi Tao und 5 weiteren Autor:innen. Die Arbeit wurde bisher 31-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Great Science & Technology Specific Project, National Science Foundation for Young Scientists of China, Program for Excellent Talents in Beijing.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Deep coalbed methane (CBM, commonly accepted as >1500 m) has enormous exploration and development potential, whereas the commercial development of deep CBM exploration areas wordwide has been quite limited. The Linxing area, with coals buried approximately 2000 m deep, shows great development potential. Based on a basic geological analysis of structural and hydrodynamic conditions, combining field tests of reservoir temperature and pressure and indoor measurements of maceral composition, proximate analysis, thermal maturity, porosity and permeability, the factors controlling deep CBM accumulations were discussed. The results show that the present burial depth of the No. 8 + 9 coal seam, mainly between 1698 and 2158 m, exhibits a high reservoir temperature (45.0–64.0 °C) and pressure (15.6–18.8 MPa), except for the uplift area caused by the Zijinshan magma event (with coal depth approximately 1000 m). The maximum vitrinite reflectance (Ro,max) of the coal varies from 1.06% to 1.47%, while the magma-influenced areas reach 3.58% with a relatively high ash content of 31.3% (air-dry basis). The gas content calculated by field desorption tests shows a wide range from 7.18 to 21.64 m3/t. The key factors controlling methane accumulation are concluded from regional geological condition variations. The north area is mainly controlled by structural conditions and the high gas content area located in the syncline zones. The center area is dominated by the Zijinshan magma, with relatively high thermal maturity and a high gas content of as much as 14.5 m3/t. The south area is developed with gentle structural variations, and the gas content is mainly influenced by the regional faults. Furthermore, the groundwater activity in the eastern section is stronger than that in the west, and the hydrodynamic stagnant areas in the western are more beneficial for gas accumulation. The coals vary from 3.35% to 6.50% in porosity and 0.08 to 5.70 mD in permeability; thus, hydrofracturing considering high temperature and pressure should be applied carefully in future reservoir engineering, and the co-production of gas from adjacent tight sandstones also should be evaluated.

Förderung

  • National Great Science & Technology Specific Project
  • National Science Foundation for Young Scientists of China
  • Program for Excellent Talents in Beijing
  • Project of Education Department of Liaoning Province
  • Doctoral research Start-up Project of Liaoning Petrochemical University

Zitieren

APA

Tao, C., Li, Y., Wang, Y., Ni, X., Wu, X., & Zhao, S. (2023). Characteristics of Deep Coal Reservoir and Key Control Factors of Coalbed Methane Accumulation in Linxing Area. Energies, 16(16), 6085. https://doi.org/10.3390/en16166085

Vancouver

Tao C, Li Y, Wang Y, Ni X, Wu X, Zhao S. Characteristics of Deep Coal Reservoir and Key Control Factors of Coalbed Methane Accumulation in Linxing Area. Energies. 2023;16(16):6085. doi:10.3390/en16166085

BibTeX
@article{Tao2023,
  author = {Tao, Chuanqi and Li, Yong and Wang, Yanbin and Ni, Xiaoming and Wu, Xiang and Zhao, Shihu},
  title = {Characteristics of Deep Coal Reservoir and Key Control Factors of Coalbed Methane Accumulation in Linxing Area},
  journal = {Energies},
  year = {2023},
  volume = {16},
  number = {16},
  pages = {6085},
  doi = {10.3390/en16166085}
}
Kostenlos starten →