EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Surrogate-Assisted Tolerance and Identifiability Analysis of Manufacturing Deviations in a 28-GHz mmWave Antenna from S11 Measurements

Chaker Essid, Linda Chouikhi, Mongi Ben Moussa, Abdelilah Mansour, Hedi Sakli

Electronics · 17.11.2026 · 15 (22) · 5360

DOI: 10.3390/electronics15225360 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Electronics, online erschienen am 17.11.2026. Verfasst von Chaker Essid und 4 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Umm al-Qura University.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper presents a surrogate-assisted study of the tolerance and of the identifiability of manufacturing deviations of a 28 GHz inset-fed microstrip patch antenna for 5G millimeter-wave applications. A Multilayer Perceptron (MLP) surrogate was trained on 500,625 (geometry, frequency) samples (625 full-wave HFSS geometries × 801 frequency points) and reaches R2 = 0.996 on unseen geometries. The geometry selected from the simulations achieves a simulated matching of −43 dB at 28 GHz, a 2.75 GHz bandwidth and a simulated gain of 4.4 dBi; the contribution of this work is not the antenna itself, which is a conventional benchmark. The fabricated prototype resonates at 28.07 GHz against 28.02 GHz in simulation, i.e., within 50 MHz (0.18%). The same full-factorial database (±100 µm around the fabricated design) shows that S11 at 28 GHz remains below −26 dB for every combination of deviations and that y1 is the geometrical parameter that most affects the resonance frequency, followed by x1, y2 and x2. A Bayesian inverse analysis based on the MLP shows, on a blind simulated test and on the measured curve, that S11 alone only partially identifies the individual deviations (only y1 is recovered, and the 90% intervals contain the true value in 50–67% of the cases). Moreover, additional ANSYS HFSS (version .13, Ansys Inc., Canonsburg, PA, USA) simulations show that a change of only −0.3% of the FR4 permittivity or −13 µm of its thickness reproduces the measured 50 MHz shift, whereas ±100 µm of any geometrical parameter shifts the resonance by at most ±40 MHz. The substrate therefore dominates over the geometrical deviations, and when a substrate nuisance parameter is included in the inverse analysis (approximate model), none of the four geometrical deviations is identified from S11. These results delimit what can and cannot be diagnosed from a single S11 measurement, and provide guidelines for the validation of fabricated mmWave antennas (direct dimensional measurements and substrate characterization).

Förderung

  • Umm al-Qura University

Zitieren

APA

Essid, C., Chouikhi, L., Moussa, M. B., Mansour, A., & Sakli, H. (2026). Surrogate-Assisted Tolerance and Identifiability Analysis of Manufacturing Deviations in a 28-GHz mmWave Antenna from S11 Measurements. Electronics, 15(22), 5360. https://doi.org/10.3390/electronics15225360

Vancouver

Essid C, Chouikhi L, Moussa MB, Mansour A, Sakli H. Surrogate-Assisted Tolerance and Identifiability Analysis of Manufacturing Deviations in a 28-GHz mmWave Antenna from S11 Measurements. Electronics. 2026;15(22):5360. doi:10.3390/electronics15225360

BibTeX
@article{Essid2026,
  author = {Essid, Chaker and Chouikhi, Linda and Moussa, Mongi Ben and Mansour, Abdelilah and Sakli, Hedi},
  title = {Surrogate-Assisted Tolerance and Identifiability Analysis of Manufacturing Deviations in a 28-GHz mmWave Antenna from S11 Measurements},
  journal = {Electronics},
  year = {2026},
  volume = {15},
  number = {22},
  pages = {5360},
  doi = {10.3390/electronics15225360}
}
Kostenlos starten →