EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Formulation and Characterization of 3D-Printable Nitrogen- and Metal-Doped Carbon Inks for ORR Electrode Applications

Joseph H. Dumont, Marcos M. Hernandez, Shaylynn L. A. Crum, Andre J. Spears, Kwan-Soo Lee

Electrochem · 19.08.2026 · 7 (3) · 23

DOI: 10.3390/electrochem7030023 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Electrochem, online erschienen am 19.08.2026. Verfasst von Joseph H. Dumont und 4 weiteren Autor:innen. Die Arbeit nennt 23 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Institute of Materials Science (IMS) at Los Alamos National Laboratory.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Additive manufacturing provides a fabrication route for electrode components with controlled macrostructure; however, printable carbon inks that also incorporate oxygen reduction reaction active precursors remain underdeveloped. Here, XC-72 carbon was combined with selected metal precursors to prepare N–C, Fe–N–C, and Pt-containing carbon ink formulations for direct ink writing. The precursor mixtures were incorporated into a polyurethane-based matrix, pyrolyzed at 900 °C, and characterized using X-ray diffraction, oscillatory rheology, rotating ring-disk electrode measurements, Brunauer–Emmett–Teller surface-area analysis, and scanning electron microscopy. XRD confirmed retention of carbon diffraction features and the formation of metal-containing crystalline phases after pyrolysis. Oscillatory rheology showed storage moduli exceeding loss moduli for the tested formulations, indicating elastic-dominant behavior suitable for shape retention during printing. For the PGM-free formulations, incorporation of nitrogen and iron precursors improved ORR onset potential, half-wave potential, limiting current density, and electron-transfer selectivity relative to the carbon control. BET analysis showed a decrease in accessible surface area after precursor incorporation, consistent with partial pore blocking or structural modification during pyrolysis. These results establish a printable formulation platform for ORR-active carbon-based inks, while future work is required to isolate the effects of printed architecture, pore hierarchy, and durability under fuel-cell operating conditions.

Förderung

  • Institute of Materials Science (IMS) at Los Alamos National Laboratory

Zitieren

APA

Dumont, J. H., Hernandez, M. M., Crum, S. L. A., Spears, A. J., & Lee, K. (2026). Formulation and Characterization of 3D-Printable Nitrogen- and Metal-Doped Carbon Inks for ORR Electrode Applications. Electrochem, 7(3), 23. https://doi.org/10.3390/electrochem7030023

Vancouver

Dumont JH, Hernandez MM, Crum SLA, Spears AJ, Lee K. Formulation and Characterization of 3D-Printable Nitrogen- and Metal-Doped Carbon Inks for ORR Electrode Applications. Electrochem. 2026;7(3):23. doi:10.3390/electrochem7030023

BibTeX
@article{Dumont2026,
  author = {Dumont, Joseph H. and Hernandez, Marcos M. and Crum, Shaylynn L. A. and Spears, Andre J. and Lee, Kwan-Soo},
  title = {Formulation and Characterization of 3D-Printable Nitrogen- and Metal-Doped Carbon Inks for ORR Electrode Applications},
  journal = {Electrochem},
  year = {2026},
  volume = {7},
  number = {3},
  pages = {23},
  doi = {10.3390/electrochem7030023}
}
Kostenlos starten →