EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Prosthesis-Based 3D Guide System for Maxillary Implant Placement: A Feasibility Study Using a Split-Mouth Evaluation

Marco Tudts iD, Tashia Moodley, Rani D'haese iD, Stefan Vandeweghe

Dentistry Journal · 01.07.2026 · 14 (7) · 395

DOI: 10.3390/dj14070395 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Dentistry Journal, online erschienen am 01.07.2026. Verfasst von Marco Tudts und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Periodontology, Dental School, Faculty of Medicine and Health Sciences, Ghent University, 9000 Ghent, Belgium. Die Arbeit nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background/Objectives: To evaluate the clinical feasibility and short-term radiographic outcomes of adapting a prosthesis-based guide system originally developed for single-implant placement for multi-implant placement in the edentulous maxilla, and to compare implant-level marginal bone change from prosthetic loading to one year between full-rough (IBT/IBNT/IBR) and hybrid-surface (MSC-IBT/MSC-IBNT) implants in a split-mouth design. Patient-reported outcomes were assessed with the OHIP-14 questionnaire.

Methods

Fifteen patients with an edentulous maxilla received four or five maxillary implants placed flaplessly using a 3D-printed prosthesis-based guide incorporating polyether-ether-ketone (PEEK) rails and interchangeable angulation-correction sleeves (0°, 12°, 24°). Implants had either a fully roughened or a hybrid (rough apical and middle third with a machined coronal collar) surface. Side allocation was non-randomized: the hybrid side was assigned by alternating sequence and three patients received only full-rough implants for prosthetic reasons. All patients followed a delayed loading protocol and received a screw-retained zirconia fixed bridge. Standardized periapical radiographs were obtained at definitive prosthetic loading (baseline) and at the 12-month follow-up. Implant-level marginal bone loss was calculated as the mean of mesial and distal measurements per implant. All radiographic measurements were performed by two independent examiners (M.T. and T.M.); intra-rater reliability (M.T., remeasurement of 10 radiographs) and inter-rater reliability (M.T. versus T.M., full dataset) were quantified by intraclass correlation coefficient (ICC; two-way mixed effects, absolute-agreement, single-measurement). The primary split-mouth surface comparison was performed at the patient level by averaging implant-level change scores within each surface for each patient and comparing the paired patient-level means with a Wilcoxon signed-rank test. No a priori sample-size calculation was performed; the study was designed as a feasibility pilot.

Results

Sixty-one implants were placed in 15 patients (seven male, eight female; mean age 62.5 ± 8.9 years; three current smokers). Four implants in three patients required removal and replacement during the observation period (three early failures, one late failure; per-implant early-failure rate of 3/61, 4.9%); one patient (P7) withdrew from clinical follow-up. Paired baseline and 12-month radiographs were available for 53 implants from 14 patients. Median implant-level marginal bone level increased from 0.38 mm (IQR 0.20–0.54) at baseline to 0.78 mm (IQR 0.47–1.32) at 12 months (paired Wilcoxon signed-rank, p < 0.001); two implants exceeded 4 mm of bone change at 12 months. In the patient-level paired surface comparison (n = 8 patients contributing at least one full-rough and one hybrid implant with paired data), full-rough implants showed less 12-month marginal bone change than hybrid implants in every paired patient (median paired difference full-rough hybrid of −0.49 mm; Hodges–Lehmann pseudo-median of 0.55 mm; paired Wilcoxon p = 0.012). OHIP-14 scores at one year (n = 14) showed a pronounced floor effect, with most patients scoring zero across most domains. Both intra-rater (M.T.) and inter-rater (M.T. versus T.M.) reliability showed good agreement (ICC = 0.85).

Conclusions

A prosthesis-based guide system originally validated for single-implant placement can be feasibly adapted for flapless multi-implant rehabilitation of the edentulous maxilla, with early clinical and radiographic outcomes broadly consistent with comparable published series. Contrary to the design rationale that a machined coronal collar would limit early crestal remodeling, full-rough implants showed less 12-month within-patient bone change than hybrid implants in the eight paired patients; this finding is preliminary and hypothesis generating given the small, unbalanced paired sample and the contrast with larger published series. The approach is best characterized as a reduced infrastructure alternative to proprietary guided-surgery platforms, remains operator dependent, and requires confirmation in formally powered, balanced split-mouth trials with concealed allocation, placement anchored bone level measurement, postoperative CBCT for deviation quantification, and longer follow-up.

Schlagwörter

Stichwörter der Autor:innen

OHIP-14edentulous maxillafull-rough implantguided implant surgeryhybrid implant surfacemarginal bone lossprosthesis-based guidesplit-mouth design

Autor:innen und Institutionen

  • Department of Periodontology, Dental School, Faculty of Medicine and Health Sciences, Ghent University, 9000 Ghent, Belgium.
  • Cosmident, Private Practice, 2500 Lier, Belgium.
  • Department of Reconstructive Dentistry, Dental School, Faculty of Medicine and Health Sciences, Ghent University, 9000 Ghent, Belgium.

ORCID-Profile: Marco Tudts, Rani D'haese

Zitieren

APA

Tudts, M., Moodley, T., D'haese, R., & Vandeweghe, S. (2026). Prosthesis-Based 3D Guide System for Maxillary Implant Placement: A Feasibility Study Using a Split-Mouth Evaluation. Dentistry Journal, 14(7), 395. https://doi.org/10.3390/dj14070395

Vancouver

Tudts M, Moodley T, D'haese R, Vandeweghe S. Prosthesis-Based 3D Guide System for Maxillary Implant Placement: A Feasibility Study Using a Split-Mouth Evaluation. Dentistry Journal. 2026;14(7):395. doi:10.3390/dj14070395

BibTeX
@article{Tudts2026,
  author = {Tudts, Marco and Moodley, Tashia and D'haese, Rani and Vandeweghe, Stefan},
  title = {Prosthesis-Based 3D Guide System for Maxillary Implant Placement: A Feasibility Study Using a Split-Mouth Evaluation},
  journal = {Dentistry Journal},
  year = {2026},
  volume = {14},
  number = {7},
  pages = {395},
  doi = {10.3390/dj14070395}
}
Kostenlos starten →