Systematic Review on the Use of 3D-Printed Models for Planning, Training and Simulation in Vascular Surgery
Systematische Übersicht zur Verwendung von 3D-gedruckten Modellen für Planung, Training und Simulation in der Gefäßchirurgie
Diagnostics · 31.07.2024 · 14 (15) · 1658
DOI: 10.3390/diagnostics14151658 ↗Auf einen Blick
Die systematische Übersicht fasst Anwendungen von 3D-gedruckten Modellen in der Gefäßchirurgie zusammen. Planung und Training schienen das Selbstvertrauen und die Leistung von Ärzt:innen zu verbessern und Prozedurzeit sowie Kontrastmittelverbrauch zu senken.
Fragestellung
Welche Anwendungen haben 3D-gedruckte Modelle für Planung, Training und Simulation in der Gefäßchirurgie?
Methode
Systematische Übersichtsarbeit; Suche in PubMed, Web of Science, Scopus und Cochrane Library bis 1. März 2024.
Ergebnisse
22 Studien wurden eingeschlossen. CTA war die wichtigste Bildgebung zur Modellerstellung; häufig genutzt wurden 3DSlicer, ITK-Snap, Mimics sowie Autodesk Meshmixer und 3-matic. PolyJet™, FDM und SLA waren die häufigsten Drucktechnologien.
Schlussfolgerung der Autor:innen
Planung und Training mit 3D-gedruckten Modellen scheinen das Vertrauen und die Leistung von Ärzt:innen zu erhöhen und die Prozedurzeit sowie den Kontrastmittelverbrauch in unterschiedlichem Ausmaß zu verringern.
Kernaussagen
- 22 Studien zu 3D-gedruckten Modellen in der Gefäßchirurgie
- CTA war die wichtigste Grundlage für die Modellerstellung
- Planung und Training schienen Performance und Vertrauen zu verbessern
Deutsche Zusammenfassung: KI-gestützt aus dem Original-Abstract erstellt; alle Zahlen wurden automatisch mit dem Original abgeglichen. Maßgeblich ist der Original-Abstract.
Kurz gefasst
Übersichtsarbeit in der Zeitschrift Diagnostics, online erschienen am 31.07.2024. Verfasst von Alexandra Catasta und 6 weiteren Autor:innen. Beteiligte Einrichtung: Vascular Surgery, Cardio-Thoracic and Vascular Department, University-Hospital of Parma, Via Gramsci 14, 43126 Parma, Italy. Die Arbeit wurde bisher 20-mal zitiert (Crossref) und nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Italian Ministry of Health (Ministero della Salute, Bando della Ricerca Finalizzata 2019).
Abstract (Originalsprache)
The use of 3D-printed models in simulation-based training and planning for vascular surgery is gaining interest. This study aims to provide an overview of the current applications of 3D-printing technologies in vascular surgery. We performed a systematic review by searching four databases: PubMed, Web of Science, Scopus, and Cochrane Library (last search: 1 March 2024). We included studies considering the treatment of vascular stenotic/occlusive or aneurysmal diseases. We included papers that reported the outcome of applications of 3D-printed models, excluding case reports or very limited case series (≤5 printed models or tests/simulations). Finally, 22 studies were included and analyzed. Computed tomography angiography (CTA) was the primary diagnostic method used to obtain the images serving as the basis for generating the 3D-printed models. Processing the CTA data involved the use of medical imaging software; 3DSlicer (Brigham and Women’s Hospital, Harvard University, Boston, MA), ITK-Snap, and Mimics (Materialise NV, Leuven, Belgium) were the most frequently used. Autodesk Meshmixer (San Francisco, CA, USA) and 3-matic (Materialise NV, Leuven, Belgium) were the most frequently employed mesh-editing software during the post-processing phase. PolyJet™, fused deposition modeling (FDM), and stereolithography (SLA) were the most frequently employed 3D-printing technologies. Planning and training with 3D-printed models seem to enhance physicians’ confidence and performance levels by up to 40% and lead to a reduction in the procedure time and contrast volume usage to varying extents.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Vascular Surgery, Cardio-Thoracic and Vascular Department, University-Hospital of Parma, Via Gramsci 14, 43126 Parma, Italy.
- Department of Medicine and Surgery, University of Parma, Via Gramsci 14, 43126 Parma, Italy.
- Diagnostic Department, University-Hospital of Parma, Via Gramsci 14, 43126 Parma, Italy.
- Center of Excellence for Toxicological Research (CERT), University of Parma, 43126 Parma, Italy.
- Italian National Research Council, Institute of Materials for Electronics and Magnetism (CNR-IMEM), 43124 Parma, Italy.
ORCID-Profile: Chiara Martini, Arianna Mersanne, Ruben Foresti, Claudio Bianchini Massoni, Paolo Perini
Förderung
- Italian Ministry of Health (Ministero della Salute, Bando della Ricerca Finalizzata 2019)
Zitieren
APA
Catasta, A., Martini, C., Mersanne, A., Foresti, R., Bianchini Massoni, C., Freyrie, A., & Perini, P. (2024). Systematic Review on the Use of 3D-Printed Models for Planning, Training and Simulation in Vascular Surgery. Diagnostics, 14(15), 1658. https://doi.org/10.3390/diagnostics14151658
Vancouver
Catasta A, Martini C, Mersanne A, Foresti R, Bianchini Massoni C, Freyrie A, et al. Systematic Review on the Use of 3D-Printed Models for Planning, Training and Simulation in Vascular Surgery. Diagnostics. 2024;14(15):1658. doi:10.3390/diagnostics14151658
BibTeX
@article{Catasta2024,
author = {Catasta, Alexandra and Martini, Chiara and Mersanne, Arianna and Foresti, Ruben and Bianchini Massoni, Claudio and Freyrie, Antonio and Perini, Paolo},
title = {Systematic Review on the Use of 3D-Printed Models for Planning, Training and Simulation in Vascular Surgery},
journal = {Diagnostics},
year = {2024},
volume = {14},
number = {15},
pages = {1658},
doi = {10.3390/diagnostics14151658}
}
EUVIMED